Symmetricom ATS-6511A Page 72 User Manual Download | Manualshive

Page: 72 / 115

background image

DOC 6511_Release K

ATS-6511A/B/C Users Guide

66

Appendix B Status Command Fields

This section provides information on the results from the status command.

ATS-6511B>status

[alarm] no alarm

Highest priority alarm.

[fiber]

Fiber Information

[chassis_delay] -3.000000000000000e-10

Chassis Calibration Value

[clock_offset] 9.497872340000000e-09

Current Clock offset from the source

[da4340delay] 0.00000000000

Fiber Dist Amp Delays

[fpga]
[delay] 0.00000000000

Internal Delays

[inputA] good

Input A Status

[inputB] good

Input B Status

[steer] -1.000000000100000e-12

Clock Steer value

[two_way]

Two Way Data Exchange Information

[channelA]

Fiber A

[4340_output] 0

0 = no 4340, # = 4340 Channel

[clock_offset] 1.000000001111078e-10

Current Fiber offset.

[direct_connect] true

True = no 4340 in the path.

[fiber_delay]

Measured fiber delays

[local] 6.887777777811110e-08

Fiber length in nSec.

[remote] 6.335555555555556e-08

Fiber length reported by 6501.

[remote_tdc_time] 2011-11-07-18:07:55

Time measurement was made.

[rxdelay] -3.690000000000000e-08

Factory Calibration values

[txdelay] -3.690000000000000e-08
[channelB]

Fiber B (same as A)

            [4340_output] 0
            [clock_offset] -6.601419878215690e-09
            [direct_connect] true
            [fiber_delay]
               [local] 5.368593644378431e-08
               [remote] 7.398039215686274e-08
            [remote_tdc_time] 2011-11-07-18:07:57
            [rxdelay] -3.650000000000000e-08
            [txdelay] -3.650000000000000e-08
   [hardware]

System Information

[fan]

Fan Status

[1] true

Fan 1

[2] true

Fan 2

[mainboard]

Unit Information

[EUID] 00:a0:69:00:03:00:00:f8

Main Board Electronic ID

[serialnum] 164233

Unit S/N

[type] 6511

Model #

[outputs]

Outputs

[enabled] true

On=Enabled, Off=Disabled

[slots]

Output Card Information

[1]

Slot #

[ports]

Port Information

[1]

Port #

[status] good

Port Status

                  [2]
                     [status] good
                  [3]
                     [status] good
                  [4]

«
...
70
71
72
73
74
...
»

Summary of Contents for ATS-6511A




















































































































Reviews:

No comments

Related manuals for ATS-6511A

Brand: NAD Pages: 32

BeoLink Passive

Brand: Bang & Olufsen Pages: 12

Brand: SOUNDIMPRESS Pages: 12

Brand: JDM Pages: 8

Brand: Analog Metric Pages: 6

Brand: Texas Instruments Pages: 10

Brand: Teac Pages: 96

Brand: JDS Labs Pages: 7

Brand: Rainbow Pages: 12

Brand: Banner Pages: 19

Brand: M-system Pages: 4

Brand: Harman Kardon Pages: 8

Brand: Fender Pages: 12

Controller LED ADT MP3-20

Brand: Botex Pages: 16

Brand: Alpine Pages: 16

Brand: HZ Sound Systems Pages: 9

Brand: Tascam Pages: 4

Brand: B2 Audio Pages: 6

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands