manualshive.com logo in svg

Symmetricom ATS-6511A, User Manual, Page: 53 / 115

Share
Download
Symmetricom ATS-6511A User Manual Download Page 53

 

DOC 6511_Release K 

 

ATS-6511A/B/C Users Guide

 

 

47 

3.

 

Inspect  the  connectors.  Verify  that  the  cable  connectors  are  not  damaged  at  the 
connection to the ATS-6511, upstream 4372A/4372A-T (ATS-6501) or TSC-4340 (1U 
1x8 Fiber Distribution Amplifier. 

5.3 Fan Filter 

The fan filters helps protect the system from accumulating dust inside the unit as well and allows 
the fans to provide the proper level of cooling for the internal components.  It is important to keep 
this filter clean to allow the proper level of air flow to prevent the system from overheating.  To 
clean the filter: 
 

1.

 

Remove the fan assembly from the front by loosening the two captive screws.  

2.

 

Remove the filter from the fan assembly. 

3.

 

Use a vacuum cleaner to clean the fan filter of any accumulated dust. 

4.

 

Re-install the filter and assembly into the chassis. Take care to feed the cable into the 
chassis while inserting the fan assembly. 

 

Summary of Contents for ATS-6511A




















































































































Reviews:

No comments