Symmetricom ATS-6511A Page 49 User Manual Download | Manualshive

Page: 49 / 115

background image

DOC 6511_Release K

ATS-6511A/B/C Users Guide

43

                     [format] B
                     [signal_word] 120
                     [type] irig
                  [4]
                     [epoch_127] false
                     [format] B
                     [signal_word] 120
                     [type] irig
   [node]
      [maintenance_mode]
         [enable] false
      [system_autoswitching_participant] true
   [pps_adjust]
      [distribution_delay] 0.00000000000
   [ptd_port]
      [averaging_interval] 10
   [reference]
      [external]
         [type] cesium
      [source] ocxo
      [timescale]
   [smcp]
   [syscfg]
      [mode] standalone
[OK] 2013-08-13T18:45:56Z

P.

At this point if there are no alarms the ATS-6511 is functioning properly. Network
connectivity should be checked to ensure that data is being transmitted properly.

Q.

If operations are normal and the setup is proper type

save

at the command prompt to

save the system default settings or

save filename

to save the settings to a different

configuration file.

Note:

If you do not save the user

default

settings the system will come up with the

factory

default

values the next time the system reboots.

«
...
47
48
49
50
51
...
»

Summary of Contents for ATS-6511A




















































































































Reviews:

No comments

Related manuals for ATS-6511A

Brand: Yamaha Pages: 2

Brand: Yamaha Pages: 35

Brand: Yamaha Pages: 20

Brand: Yamaha Pages: 8

Brand: Warwick Pages: 14

Brand: Tiger Electronics Pages: 8

Brand: Befaco Pages: 6

9440A POWER AMPLIFIER

Brand: Altec Lansing Pages: 4

Brand: Crown Pages: 72

Brand: Thinuna Pages: 12

Brand: Fenton Pages: 7

Brand: Clockaudio Pages: 3

Brand: Triode Lab Pages: 9

Brand: VINCENT Pages: 60

Pro-Ject Tube Box SE

Brand: Pro-Ject Audio Systems Pages: 3

Brand: Total Mobile Audio Pages: 11

Brand: DSM Pages: 8

Brand: Marantz Pages: 27

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands