Symmetricom ATS-6511A Page 47 User Manual Download | Manualshive

Page: 47 / 115

background image

DOC 6511_Release K

ATS-6511A/B/C Users Guide

41

N.

The last set of data [unit] will display the system network information, serial number, the
system startup time, the uptime since the last power cycle, the software version running
on the system, and the time the

status

command was executed.

  [unit]
    [network]
      [MAC] 00:A0:69:02:00:AD
      [broadcast] 192.168.150.255
      [default_gateway]
      [ip] 192.168.150.85
      [netmask] 255.255.255.0
   [serial_number] P44308
   [start] 2013-08-05-14:23
   [uptime] 8 days, 4 hours, 20 minutes
   [ver] tflex-5-1-0

O.

Send the

settings

command and verify the user defined set up parameters are correct.

ATS-6511A>settings

   [command_port]
      [prompt]
         [enable] true
         [text] 6511C_1>
   [diaglog]
      [cpld4370] info
      [fiber] info
      [kas2] info
      [lnsrawstate] info
      [software] info
      [switching] info
      [timecode] info
      [tsc4370] info
      [tsgather] info
      [warmstart] info
   [fiber]
      [delay]
         [channelA] 0.00000000000
         [channelB] 0.00000000000
      [delay_diff]
         [channelA] 0.00000000000
         [channelB] 0.00000000000
      [mode] two_way
      [pll]
         [proportional_gain] 1.000000000000000e-02
      [switching]
         [auto_rearm] true
         [master] A
         [min_valid_time] 30
         [mode] auto
   [hardware]
      [enable_fp_button] true
      [slots]
         [1]
            [tsc4373]
               [ports]
                  [1]
                     [pps_period] 1.00000000000

«
...
45
46
47
48
49
...
»

Summary of Contents for ATS-6511A




















































































































Reviews:

No comments

Related manuals for ATS-6511A

Brand: E&I Pages: 13

Brand: Pangea Pages: 7

Brand: TC Electronic Pages: 45

Brand: HR Pages: 12

Brand: RAM Pages: 17

ZOTL40 Reference

Brand: Linear Tube Audio Pages: 8

Brand: PSSO Pages: 28

Brand: SilverStone Pages: 8

Kommander-KA Series

Brand: K-array Pages: 24

Brand: Studiomaster Pages: 6

Brand: Montarbo Pages: 10

Brand: Woo Audio Pages: 19

Brand: Hegel Pages: 8

Brand: Hegel Pages: 20

CE 1000 A. & E.

Brand: Crown Pages: 1

Brand: ATC Electronics Pages: 20

Brand: Block Pages: 31

Brand: Tone King Pages: 20

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands