manualshive.com logo in svg

Symmetricom ATS-6511A, User Manual

The Symmetricom ATS-6511A is a high-quality precision time and frequency analyzer. It comes with a comprehensive User Manual that provides detailed instructions on operating the device effectively. You can easily download the manual for free from our website, manualshive.com, to unlock the full potential of this exceptional product.

Share
Download
background image

 

DOC 6511_Release K 

 

ATS-6511A/B/C Users Guide

 

 

74 

Status: 

If the system time is not set it will show boot + N seconds. 

2013-08-12-21:11:28.925 status:alarm=no alarm 
boot+128sec status:fan:1=1 
boot+128sec status:fan:2=1 
boot+128sec status:fiber:chassis_delay=1.850000000000000e-08 
boot+248sec status:fiber:clock_offset=9.070434782999997e-09 
boot+128sec status:fiber:da4340delay=0.00000000000 
boot+128sec status:fiber:fpga:delay=0.00000000000 
2013-08-12-21:10:28.077 status:fiber:inputA=good 
2013-08-12-21:10:32.014 status:fiber:inputB=good 
boot+128sec status:fiber:two_way:channelA:rxdelay=-4.628000000000000e-08 
2013-08-12-22:52:10.022 status:fiber:two_way:channelA:tdc:local=7.141304347800000e-08 
boot+128sec status:fiber:two_way:channelA:txdelay=-4.628000000000000e-08 
boot+128sec status:fiber:two_way:channelB:rxdelay=-4.619000000000000e-08 
2013-08-12-22:52:11.037 status:fiber:two_way:channelB:tdc:local=7.088888888900000e-08 
boot+128sec status:fiber:two_way:channelB:txdelay=-4.619000000000000e-08 
boot+128sec status:hardware:mainboard:EUID=00:30:96:02:00:00:01:ec 
boot+128sec status:hardware:mainboard:serialnum=154825 
boot+128sec status:hardware:mainboard:type=6511 
boot+128sec status:hardware:outputs:enabled=1 
2013-08-12-19:12:45.137 status:hardware:outputs:slots:1:ports:1:status=good 
2013-08-12-19:12:45.139 status:hardware:outputs:slots:1:ports:2:status=good 
2013-08-12-19:12:45.142 status:hardware:outputs:slots:1:ports:3:status=good 
2013-08-12-19:12:45.150 status:hardware:outputs:slots:1:ports:4:status=good 
boot+134sec status:hardware:outputs:slots:1:power=enabled 
boot+134sec status:hardware:outputs:slots:1:type=4394A 
2013-08-12-19:12:45.176 status:hardware:outputs:slots:2:ports:1:status=good 
2013-08-12-19:12:45.179 status:hardware:outputs:slots:2:ports:2:status=good 
2013-08-12-19:12:45.182 status:hardware:outputs:slots:2:ports:3:status=good 
2013-08-12-19:12:45.189 status:hardware:outputs:slots:2:ports:4:status=good 
boot+137sec status:hardware:outputs:slots:2:power=enabled 
boot+137sec status:hardware:outputs:slots:2:type=4394A 
2013-08-12-19:12:48.418 status:hardware:outputs:slots:3:ports:1:status=good 
2013-08-12-19:12:48.423 status:hardware:outputs:slots:3:ports:2:status=good 
2013-08-12-19:12:48.429 status:hardware:outputs:slots:3:ports:3:status=good 
2013-08-12-19:12:48.432 status:hardware:outputs:slots:3:ports:4:status=good 
2013-08-12-19:12:47.322 status:hardware:outputs:slots:3:power=enabled 
boot+137sec status:hardware:outputs:slots:3:type=4395B-10 
boot+128sec status:hardware:outputs:slots:4:type=empty 
2013-08-12-19:12:46.264 status:hardware:outputs:slots:5:ports:1:status=good 
2013-08-12-19:12:46.266 status:hardware:outputs:slots:5:ports:2:status=good 
2013-08-12-19:12:46.273 status:hardware:outputs:slots:5:ports:3:status=good 
2013-08-12-19:12:46.275 status:hardware:outputs:slots:5:ports:4:status=good 
boot+140sec status:hardware:outputs:slots:5:power=enabled 
boot+140sec status:hardware:outputs:slots:5:type=4387A 
boot+128sec status:hardware:outputs:slots:6:type=empty 
2013-08-12-19:12:45.058 status:hardware:outputs:warmstartable=1 
boot+128sec status:hardware:power:numsupplies=2 
boot+140sec status:hardware:power:supplies:1:status=good 
boot+140sec status:hardware:power:supplies:1:type=4385A 
boot+140sec status:hardware:power:supplies:2:status=good 
boot+140sec status:hardware:power:supplies:2:type=4385A 
boot+244sec status:health:clock_wander:active=0 
boot+244sec status:health:clock_wander:cleared:what=Clock wander is less than 100.000000ns 
boot+244sec status:health:clock_wander:cleared:when=1998-01-01-00:04:21.384 
boot+242sec status:health:clock_wander:occurrences=1 
boot+242sec status:health:clock_wander:set:what=Clock wander exceeded 100.000000ns 
boot+242sec status:health:clock_wander:set:when=1998-01-01-00:04:19.273 

Summary of Contents for ATS-6511A




















































































































Reviews:

No comments

Related manuals for ATS-6511A

Jensen A1000 Owner'S Manual And Installation Instructions preview
A1000
Brand: Jensen Pages: 6
DAD DP8000 User Manual preview
DP8000
Brand: DAD Pages: 24
CAD Audio HA4 Specifications preview
HA4
Brand: CAD Audio Pages: 2
µ-Dimension ProX 840.4 COMP Manual preview
ProX 840.4 COMP
Brand: µ-Dimension Pages: 12
Arcam rPhono Connections And Quickstart Manual preview
rPhono
Brand: Arcam Pages: 84
Vox AmPlug User Manual preview
AmPlug
Brand: Vox Pages: 2
Nady Audio PHP-3 User Manual preview
PHP-3
Brand: Nady Audio Pages: 2
Biamp DA28R Operation Manual preview
DA28R
Brand: Biamp Pages: 13
Klipsch ProMedia DD-5.1 User Manual preview
ProMedia DD-5.1
Brand: Klipsch Pages: 34
JBL BPx1100.1 Owner'S Manual preview
BPx1100.1
Brand: JBL Pages: 8
NAD 163AV Owner'S Manual preview
163AV
Brand: NAD Pages: 33
Harman JBL Club-4505 Service Manual preview
JBL Club-4505
Brand: Harman Pages: 21
J&M Corporation XXRK-630SP4-14SG-ST4 Installation Instructions Manual preview
XXRK-630SP4-14SG-ST4
Brand: J&M Corporation Pages: 9
Vitus Audio SM-101 Manual preview
SM-101
Brand: Vitus Audio Pages: 4
Marantz PM8200 Service Manual preview
PM8200
Brand: Marantz Pages: 17
Ayre P-5XE Owner'S Manual preview
P-5XE
Brand: Ayre Pages: 24
K-array Kommander-KA02 User Manual preview
Kommander-KA02
Brand: K-array Pages: 24
Ibanez Troubadour T80IISM Owner'S Manual preview
Troubadour T80IISM
Brand: Ibanez Pages: 28

Brands by name

Popular brands

Load more brands