Symmetricom ATS-6511A Page 45 User Manual Download | Manualshive

Page: 45 / 115

background image

DOC 6511_Release K

ATS-6511A/B/C Users Guide

39

[occurrences] 0

on the status report.

         [4]
            [active] false
            [occurrences] 0
         [5]
            [active] false
            [occurrences] 0
         [6]
            [active] false
            [occurrences] 0
      [outputs_disabled]
         [active] false
         [occurrences] 0
      [over_temperature]
         [active] false
         [occurrences] 0
      [power_supply]
         [1]
            [active] false
            [occurrences] 0
         [2]
            [active] false
            [occurrences] 0

I.

The  [ref_unlocked]  fields  are  reporting  the  clock  status  and  system  performance
information.    The  reference  should  be  locked  ([ref_unlocked]  [active]  =  false)  and  the
TCXO should not have any active alarms ([tcxo_failure] [active] = false).  The reference
may report it is unlocked and the remote_tdc_starvation may show one occurrence.  This
is typical after a power up or coldstart and these conditions will clear once locked to the
fiber inputs.

[ref_comm_error]
         [active] false
         [occurrences] 0
      [ref_missing]
         [active] false
         [occurrences] 0

      [ref_unlocked]
         [active] false
         [cleared]
            [what] LNS is locked
            [when] 2011-11-07-17:11:01.316
         [occurrences] 2
         [set]
            [what] LNS is unlocked

Typical at start up.

            [when] 2011-11-07-17:10:44.886
      [remote_tdc_starvation]
         [active] false
         [cleared]
            [what] Receiving remote TDCs
            [when] 2011-11-07-17:11:01.316
         [occurrences] 1
         [set]
            [what] Not receiving remote TDCs

Typical at start up.

            [when] 2011-11-07-17:10:39.722
      [syscfg]
         [active] false
         [occurrences] 0
      [tcxo_failure]

«
...
43
44
45
46
47
...
»

Summary of Contents for ATS-6511A




















































































































Reviews:

No comments

Related manuals for ATS-6511A

Brand: Ecler Pages: 20

Brand: Ecleree Pages: 28

Brand: Ecleree Pages: 42

Brand: Apogee Pages: 16

VIV Six Five Series

Brand: Memphis Pages: 16

Brand: deBont Pages: 10

redback A 4140 2 x 100W

Brand: Altronics Pages: 4

ATLONA AT-RON-442

Brand: Panduit Pages: 12

Brand: Nady Audio Pages: 2

Brand: D.W. Fearn Pages: 37

Brand: Marantz Pages: 46

Brand: McIntosh Pages: 20

Brand: Harman Kardon Pages: 50

Classic Chorus 212

Brand: Peavey Pages: 19

Brand: JBL Pages: 31

Brand: Inline Pages: 11

Brand: Kustom Pages: 8

Brand: Amate Audio Pages: 59

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands