Symmetricom ATS-6511A Page 33 User Manual Download | Manualshive

Page: 33 / 115

background image

DOC 6511_Release K

ATS-6511A/B/C Users Guide

27

significant software/firmware changes that necessitate this update be done by completely
replacing the flash card. Please refer to the software release notes to accomplish this update.

3.3.2.1 Flash Card Replacement

This requires removing the currently installed flash disk and installing a new one which has the
updated software. Power the system down, press and release the SD card located in the SD Card
slot on the front panel. Remove the current flash disk and replace it with the new flash. Once the
new flash is securely installed restore power to the unit.

Caution:

The system network and user configuration settings are

NOT

saved and the system

will need to be completely set up with the network and system settings.

Figure 8 Front Panel Flash Card

3.3.2.2 Remote Software Update

The ATS-6511 software can be updated remotely over the network. Users can download the new
software image onto the flash and run the

software_update

command to load the new software

onto  the  flash.    Once  the  software  has  successfully  been  updated  the  system  will  automatically
reboot.  The system network and user configuration files will be saved and reloaded onto the new
software  image  and  do  not  require  any  additional  steps.    To  update  the  system  with  the  new
software:

1.

FTP into the system and log in (username: update, password: update).

2.

Switch to binary transfer mode if needed, upload (put) the .iso file, and quit ftp.

localhost> ftp 192.168.1.254
Connected to 192.168.1.254.
220 tflex FTP server (Version 6.00LS) ready.
Name (192.168.1.254:localhost): ftp
331 Guest login ok, send your email address as password.
Password:
230 Guest login ok, access restrictions apply.
Remote system type is UNIX.

Using binary mode to transfer files.
ftp> binary

Use this command to switch to binary if needed.

200 Type set to I.

ftp> > put tflex-5-1-0.iso
local: tflex-5-1-0.iso remote: tflex-5-1-0.iso
227 Entering Passive Mode (192,168,150,61,192,177)
150 Opening BINARY mode data connection for 'tflex-5-1-0.iso'.
226 Transfer complete.
18026496 bytes sent in 36.7 secs (491.34 Kbytes/sec)

«
...
31
32
33
34
35
...
»

Summary of Contents for ATS-6511A




















































































































Reviews:

No comments

Related manuals for ATS-6511A

Brand: LABTEC Pages: 12

Brand: Sansui Pages: 16

Brand: JEFF ROWLAND Pages: 14

Brand: JBL Pages: 10

Brand: NAD Pages: 20

Brand: Harman Kardon Pages: 9

Brand: Eagletone Pages: 3

Brand: DaytonAudio Pages: 4

Brand: McIntosh Pages: 20

Brand: Ltc Audio Pages: 5

Brand: Com-Power Pages: 15

Brand: Audiovox Pages: 12

Brand: Park Pages: 24

Brand: Laney Pages: 16

Brand: Symetrix Pages: 11

Brand: Sansui Pages: 24

Brand: Lightspeed Pages: 26

Brand: Rockbox Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands