Sungrow SG285HX User Manual Download Page 8

Page: 8 / 128

4.4.2 Hoisting Transport...............................................................................24

4.5 Installing the mounting-bracket ......................................................................26

4.5.1 Bracket-Mounted Installation................................................................27

4.5.2 Wall-Mounted Installation.....................................................................29

4.5.3 Pole-Mounting ....................................................................................32

4.6 Installing the Inverter.....................................................................................35

5 Electrical Connection

.....................................................................................36

5.1 Safety Instructions ........................................................................................36

5.2 Terminal Description .....................................................................................37

5.3 Electrical Connection Overview .....................................................................38

5.4 Crimp OT / DT terminal .................................................................................42

5.5 External Protective Grounding Connection .....................................................43

5.5.1 External Protective Grounding Requirements ........................................43

5.5.2 Connection Procedure.........................................................................43

5.6 AC Cable Connection ...................................................................................44

5.6.1 AC Side Requirements ........................................................................44

5.6.2 Requirements for OT/DT Terminal ........................................................47

5.6.3 Connection Procedure of One Wire per Phase with Multi-core

Cable ............................................................................................48

5.6.4 Connection Procedure of Two Wires per Phase with Multi-core

Cable ............................................................................................52

5.7 DC Cable Connection ...................................................................................57

5.7.1 PV Input Configuration ........................................................................58

5.7.2 Assembling the PV Connectors ............................................................59

5.7.3 Installing the PV Connector..................................................................61

5.8 Wiring of Tracking System Power Cable (Optional) .........................................62

5.9 RS485 Connection(COM1)............................................................................64

5.9.1 Interface Description ...........................................................................64

5.9.2 RS485 Communication System............................................................64

5.9.3 Connection Procedure.........................................................................65

5.10 Dry Contact Connection(COM2) ..................................................................68

5.10.1 Interface Description .........................................................................68

5.10.2 Dry Contact Function .........................................................................69

5.10.3 Connection Procedure .......................................................................70

5.11 PLC Communication Connection .................................................................73

6 Commissioning

...............................................................................................75

Summary of Contents for SG285HX

































































































































Search results

Summary of Contents for SG285HX

Reviews:

Related manuals for SG285HX

Brands by name

Popular brands

Sungrow SG285HX, User Manual

Search results

Summary of Contents for SG285HX

Reviews:

Related manuals for SG285HX

Brands by name

Popular brands