Sungrow SG285HX User Manual Download Page 5

Page: 5 / 128

III

Symbols

This manual contains important safety instructions, which are highlighted with the following

symbols, to ensure personal and property safety during usage, or to help optimize the prod-

uct performance in an efficient way.

Please carefully understand the meaning of these warning symbols to better use the manual.

Indicates high-risk potential hazards that, if not avoided, may lead to death or seri-

ous injury.

Indicates moderate-risk potential hazards that, if not avoided, may lead to death or

serious injury.

Indicates low-risk potential hazards that, if not avoided, may lead to minor or mod-

erate injury.

Indicates potential risks that, if not avoided, may lead to device malfunctions or fi-

nancial losses.

“NOTE” indicates additional information, emphasized contents or tips that may be

helpful, e.g., to help you solve problems or save time.

Summary of Contents for SG285HX

































































































































Search results

Summary of Contents for SG285HX

Reviews:

Related manuals for SG285HX

Brands by name

Popular brands

Sungrow SG285HX, User Manual

Search results

Summary of Contents for SG285HX

Reviews:

Related manuals for SG285HX

Brands by name

Popular brands