17
P26
Parameter 26 is the Third Party Interface (TPI) Mode toggle. The default is 0 for disabled. The Intellitan
Plus timer has a TPI jack built in to the timer i
ts
elf. This jack replaces the need for a second or additional
interface when using other timer systems. The TPI jack is located next to the two network jacks on the top
of the tanning unit (under the hinge cover). It is the larger of the three jacks and comes with a unused
modular plug in the jack. When using the Intellitan Plus timer in TPI mode the Intellitan Plus looks for
control voltage (5-30v) on the outside two wires of the modular cable plugged into the TPI port. When this
voltage is seen, the maximum
ta
nning time is sent to the timer and the
ta
nning unit is s
ta
rted. Any
session delay should be programmed on the third
pa
rty timer and the Intelli
ta
n session delay should be
set to 0. The front rail keys are locked in TPI mode.
This feature is only available with software level
16 or higher.
To Change Parameter 26, TPI Mode
Press
“Reset”
once then release it, the display will begin to flash. Now press
"up" u
ntil 0001 is displayed,
press
“Reset”
once and release it. Next cycle the power to the timer and
tan
ning unit off and back on. The
TPI Mode is now enabled. To disable this function change p
ar
ameter 26 back to 0000.
Now press
s
once and release it to reach
Parameter 27 (P27), Timer Protocol Option.
P27
Parameter 27 is the Timer Protocol Option. The default is 0001 for Intelli
ta
n Protocol. The timer protocol
option allows the salon owner to change timer network protocols from the Intelli
tan
Network to the T-Max
1
protocol for use with the T-Max Manager. For additional information please consult th
e T-Max
documentation.
This feature is only available with software level 16 or higher.
To Change Parameter 27, Timer Protocol Option
Press
“Reset”
once then release it, the display will begin to flash. Now press
"up"
until 0001 is displayed,
press
“Reset”
once and release it. Next cycle the power to the timer and
tan
ning unit off and back on.
The T-Max Protocol is now on. To turn off this function change parameter 27 back to 0000 using the
parameter edit instructions in the T-Max documentation. Y
ou can not use a CCS-1 or IPI with a timer
using T-Max Protocol.
Now press
"up"
once and release it to reach
Parameter 28 (P28),
To
tal Operating Cost.
P28
Parameter 28 is the Total Operating Cost Accumulator. This parameter tracks total operating costs of the
tanning unit based upon parameter 17, session cost per minute. This parameter is displayed in dollars and
tenths and rolls over at $999.9. The Total Operating Cost Accumulator can be reset to 0 at anytime in
order to track or determine daily, weekly, monthly, quarterly, or annual operating cos
ts
.
To Change Parameter 28, Total Operating Cost
Press
“Reset”
once then release it, the display will begin to flash. Now press
"up"
until 0000 is displayed,
press
“Reset”
once and release it. The Total Operating Cost is now reset to 0 and will begin accumulating
at the next session.
Parameter Detail
Summary of Contents for Radius 252
