16
P18
Parameter 18 is the Session Counter. The session counter displays the to
tal
number of times a session
has been started since first day of operation. The session counter counts from 0000 to 9999 then rolls
over. The session counter cannot be adjusted or reset.
Now press
s
once and release it to reach
Parameter 19 (P19), Total Hour Accumulation.
P19
Parameter 19 is the total hour accumulator. This accumulator displays the to
tal
number hours on the unit
since first day of operation. The accumulator counts from 0000 to 9999 then rolls over. The total hour
accumulator cannot be adjusted or reset.
Now press
s
once and release it to reach
Parameter 24 (P24), Continuous Countdown Mode.
Note:
Parameters 20-23 are reserved for factory use.
P24
Parameter 24 is the continuous countdown mode toggle. The default is 0 for disabled. The continuous
countdown mode allows the salon owner to maintain a tighter schedule by disabling the pause function of
the timer thus allowing the tanning time to continue to count down even if the lamps are turned off by
pressing the start/stop key.
This feature is only available with software level 16 or higher.
To Change Parameter 24, Continuous Countdown Mode
Press
“Reset”
once then release it, the display will begin to flash. Now press
"up"
until 0001 is displayed,
press
“Reset”
once and release it. Next cycle the power to the timer and
tann
ing unit o
ff
and back on. The
Continuous Countdown Mode is now enabled. To disable this function change
par
ameter 24 back to 0000.
Now press
"up"
once and release it to reach
Parameter 25 (P25), Keylock Configuration.
P25
Parameter 25 is the keylock configuration option. The default is 3 for 30 seconds. The keylock configuration
option allows the salon owner to maintain a higher sense of security by locking out the front rail keys in
several specified intervals while the timer is connected to a network
.
.
This feature is
only available with
software level 16 or higher.
The keylock intervals are:
0 - Lock keys and release only when power cycled.
1 - Lock keys and release only when parameter is changed to an option other than 01.
2 - Lock keys and release only after the network cable has been removed for 2 minutes.
3 - Lock keys and release only after the network cable has been removed for 30 seconds.
WARNING:
If you set parameter 25 to 01 (Lock until
par
ameter changed) you will be unable to change this
parameter or unlock the front rail keys without the use of a CCS-1 or other control device
. T
he Intellitan
Protocol Interface (IPI) does not edit this or any other
pa
rameter.
To Change Parameter 25, Keylock Configuration
Press
“Reset”
once then release it, the display will begin to flash. Now press
"up"
until the desired option
0,1,2,3 is displayed, press
“Reset”
once and release it. Next cycle the power to the timer and
tan
ning
unit off and back on. The Keylock Configuration is now saved.
Now press
s
once and release it to reach
Parameter 26 (P26), TPI Interface Enable.
Parameter Detail
Summary of Contents for Radius 252
