Sun Microsystems StorEdge D2 Installation, Operation And Service Manual Download Page 115

Page: 115 / 118

Index-1

Index

accessing Sun documentation online, xv
Acrobat Reader, 1-4
Adobe Acrobat Reader, 1-4

blinking LEDs defined, 1-2
books to read before proceeding, xii

cabinet

mounting parts, 1-4

cluster configuration, 1-22
comments on documentation, xvi
components

at the back of the array, 1-10
at the front of the array, 1-6
removable, 1-5

computer room map, 2-4
configuration

cluster, 1-22
options switch bank, 1-14
single-bus, 1-20
split-bus, 1-21
supported, 1-19

connections, SCSI, 1-15
controller module, power cord connector

location, 1-16

D2 array

finding by unit ID, 3-14
health monitoring, 3-4
overview, 1-1
setting up and configuring, 2-1

before you begin, 2-2
configure and cable, 2-6
configure on a host, 2-8
mount the array on a desktop, 2-5

daisy-chaining, 1-2
Declaration of Conformity, B-3
device name

and SCSI ID finding, 3-10
finding, 3-8

device naming conventions, 4-4
disk

drive identify section, 3-11
drives, Ultra3 SCSI, 1-5
faulty, 3-7
finding device name, 3-8
finding device name and SCSI ID, 3-10
labels, 1-9
slots, access to, 1-7

disk or enclosure

finding, 3-12

document comments, xvi
documentation, related, xiv
door, 1-7

electrostatic discharge (ESD) precautions, 4-3

Summary of Contents for StorEdge D2























































































































Search results

Summary of Contents for StorEdge D2

Reviews:

Related manuals for StorEdge D2

Brands by name

Popular brands

Sun Microsystems StorEdge D2, Installation, Operation And Service Manual

Search results

Summary of Contents for StorEdge D2

Reviews:

Related manuals for StorEdge D2

Brands by name

Popular brands