Sun Microsystems StorEdge D2 Installation, Operation And Service Manual Download Page 65

Page: 65 / 118

4-1

C H A P T E R

Adding and Replacing FRUs

This chapter describes how to remove and replace Field Replaceable Units (FRUs)
and how to add more disk drives. This chapter contains the following sections:

■

“Hot- and Cold-Pluggable FRUs” on page 4-2

■

“ESD Precautions” on page 4-3

■

“Removing and Replacing a Disk Drive” on page 4-4

■

“Removing and Replacing a Fan” on page 4-14

■

“Removing and Replacing a Power Supply” on page 4-16

■

“Removing and Replacing an ESM” on page 4-18

■

“Replacing the Chassis” on page 4-23

This chapter contains the following procedures:

■

“To Prepare to Replace a Disk Drive (UNIX)” on page 4-6

■

“To Prepare to Replace a Disk Drive (VxVM)” on page 4-8

■

“To Remove a Disk Drive” on page 4-9

■

“To Install a Disk Drive” on page 4-10

■

“To Restore a File System (UNIX)” on page 4-12

■

“To Re-Create a VxVM Configuration on the New Disk (VxVM)” on page 4-13

■

“To Remove and Replace a Fan Canister” on page 4-14

■

“To Remove and Replace a Power Supply” on page 4-16

■

“To Remove an ESM” on page 4-18

■

“To Install an ESM” on page 4-21

■

“To Remove the Removable Components from the Chassis” on page 4-24

■

“To Remove and Re-Attach the Mounting Tray” on page 4-25

■

“To Replace the Removable Components in the Chassis” on page 4-26

■

“To Reconfigure the Array on the Host” on page 4-27

Summary of Contents for StorEdge D2























































































































Search results

Summary of Contents for StorEdge D2

Reviews:

Related manuals for StorEdge D2

Brands by name

Popular brands

Sun Microsystems StorEdge D2, Installation, Operation And Service Manual

Search results

Summary of Contents for StorEdge D2

Reviews:

Related manuals for StorEdge D2

Brands by name

Popular brands