Sun Microsystems StorEdge D2 Installation, Operation And Service Manual Download Page 37

Page: 37 / 118

Chapter 1

Sun StorEdge D2 Array Overview

1-21

1.8.2

Split-Bus Configuration

A split-bus configuration splits a single Sun StorEdge D2 array between two ESMs,
with each ESM controlling half the disks. (

FIGURE 1-8

shows how the disks are

numbered.) The array can then be used either as two independent storage
subsystems or as a single high-availability system.

■

Two ESMs must be installed

■

Switch number 1 in the switch bank on the front of both ESMs must be set Down.

FIGURE 1-14

shows the split-bus configuration with two ESMs connected to two

different HBAs on a single host. The array is configured in this example for high
availability. In this configuration, data is mirrored in the two separate sets of disks.

FIGURE 1-14

High-Availability Split-Bus Configuration With Two ESMs, Two Host
Adapters, and a Single Host

Note –

The SCSI cable from a host can be connected to either the SCSI-A or SCSI-B

connector on the ESM.

Summary of Contents for StorEdge D2























































































































Search results

Summary of Contents for StorEdge D2

Reviews:

Related manuals for StorEdge D2

Brands by name

Popular brands

Sun Microsystems StorEdge D2, Installation, Operation And Service Manual

Search results

Summary of Contents for StorEdge D2

Reviews:

Related manuals for StorEdge D2

Brands by name

Popular brands