Sun Microsystems StorEdge D2 Installation, Operation And Service Manual Download Page 18 | Manualshive

Page: 18 / 118

background image

1-2

Sun StorEdge D2 Array Installation, Operation, and Service Manual • February 2002

1.1

Description

The Sun StorEdge D2 array is a four rack unit (4 RU) JBOD (Just a Bunch of Disks),
direct-attach, high-performance. storage subsystem containing up to twelve Ultra3
disks. The array can be managed with storage management software, such as
Solstice DiskSuite software or VERITAS Volume Manager installed on the host.

An environmental services module (ESM) monitors the status of the enclosure using
light-emitting-diodes (LEDs) to display each component’s health and activity.

Note –

The terms “flashing” and “blinking” have slightly different meanings when

they are used in the description of an LED. The rate of “flashing” varies according to
the rate of occurrence of whatever events the LED is indicating, while the rate of
“blinking” is fixed.

The ESM also enables remote environmental monitoring from a host by means of the
SCSI Accessed Fault-tolerant Enclosure

(

SAF-TE) protocol through the low voltage

differential (LVD) SCSI connection.

Each ESM has two independent Ultra3 160 MB SCSI bus connections. Daisy-chaining
is not supported.

«
...
16
17
18
19
20
...
»

Summary of Contents for StorEdge D2























































































































Reviews:

No comments

Related manuals for StorEdge D2

G-DRIVE mobile USB

Brand: G-Technology Pages: 13

MARK V Model 520

Brand: Shopsmith Pages: 32

G-DRIVE mobile USB

Brand: G-Technology Pages: 32

Barracuda 180 Family

Brand: Seagate Pages: 2

Brand: SanDisk Pages: 2

Brand: Fastora Pages: 2

Brand: Lakeshore Pages: 2

Brand: Powerline Pages: 2

Brand: Digital Equipment Pages: 70

WD10000CSRTL - Caviar GreenPower 1TB SATA Hard Drive

Brand: Western Digital Pages: 2

Superstor GL-119

Brand: HTP Pages: 12

Brand: Acomdata Pages: 21

Brand: WOOD feeling Pages: 27

Brand: Weather Guard Pages: 15

Brand: Quantum Pages: 3

Brand: Coolmax Pages: 2

Brand: Coolmax Pages: 5

Brand: Arrow Pages: 32

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands