Sun Microsystems StorEdge D2 Installation, Operation And Service Manual Download Page 21 | Manualshive

Page: 21 / 118

background image

Chapter 1

Sun StorEdge D2 Array Overview

1-5

1.4

Software Options

See the

Sun StorEdge D2 Array Release Notes

for a list of qualified storage

management software and the revision levels that can be used with the Sun
StorEdge D2 array.

1.5

Removable Components

The Sun StorEdge D2 array has the following field replaceable units (FRUs):

■

One or two ESMs

■

Two power supplies

■

Two fan canisters with two fans each

■

Up to twelve Ultra3 SCSI disk drives

■

The chassis with the front door and the midplane (replaced as a single unit)

Each FRU has a set of LEDs that indicate health and status. Descriptions of all the
FRUs and LED’s states are given later in this chapter.

See Chapter 4 for procedures to replace failed components.

Caution –

Do not operate the Sun StorEdge D2 array for extended periods with any

components missing. If the array has only one ESM or less than 12 disk drives, make
sure that all empty slots are filled with fillers. The fillers act as air baffles that enable
the system to maintain optimal cooling. If all slots are not filled, high temperatures
can result, which can damage system components.

«
...
19
20
21
22
23
...
»

Summary of Contents for StorEdge D2























































































































Reviews:

No comments

Related manuals for StorEdge D2

Brand: Husky Pages: 8

Brand: MSW Pages: 46

G-DRIVE mobile USB

Brand: G-Technology Pages: 32

Brand: Sako Pages: 19

CERTA CTTSCT5DRWA

Brand: Kogan Pages: 8

SmartStore SM2007

Brand: Riverlea Pages: 16

Brand: QNAP Pages: 68

Galaxy A16F-G2422

Brand: Rorke Data Pages: 108

Brand: Thunderbolt Pages: 37

Brand: Cavalry Pages: 16

Brand: Cavalry Pages: 16

CADA-C32A Series

Brand: Cavalry Pages: 18

Brand: Dedicated Micros Pages: 12

Brand: SmartStore Pages: 16

Brand: OWIM Pages: 13

Brand: OWC Pages: 8

Brand: Nextorage Pages: 21

G-SPEED SHUTTLE

Brand: G-Technology Pages: 8

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands