Sun Microsystems StorEdge D2 Installation, Operation And Service Manual Download Page 58

Page: 58 / 118

3-8

Sun StorEdge D2 Array Installation, Operation, and Service Manual • February 2002

▼

To Find the Device Name of a Faulty Disk

Do this procedure to find the device name (c

) of the disk that failed. If needed,

see “Device Naming Conventions” on page 4-4.

1. If disk management software is being used on the host connected to the array, find

the device name of the failed disk by following the applicable procedure in the
documentation that came with the software.

Different applications provide various levels of error logging. In general, you can
find messages about failing or failed disks in your system’s console window.

2. If no disk management software is being used, find the device name of the failed

disk in

/var/adm/messages

Summary of Contents for StorEdge D2























































































































Search results

Summary of Contents for StorEdge D2

Reviews:

Related manuals for StorEdge D2

Brands by name

Popular brands

Sun Microsystems StorEdge D2, Installation, Operation And Service Manual

Search results

Summary of Contents for StorEdge D2

Reviews:

Related manuals for StorEdge D2

Brands by name

Popular brands