SRAM RockShox Deluxe RLR Service Manual Download Page 39 | Manualshive

Page: 39 / 58

SRAM RockShox Deluxe RLR Service Manual Download Page 39

39

Piston Service

Remove the inner o-ring, located at the base of the threads in the seal

head/air piston.
Install a new o-ring, and apply a liberal amount of grease to the o-ring

and bushing.

Install the seal head/air piston onto the damper shaft.

Clamp the damper shaft into the RockShox® Rear Shock Vise Block.

NOTICE

To prevent damage to the seal head/air piston, position the shaft in the

vise so that the piston and IFP reservoir are clear of the vise jaws.

Install the main piston assembly that was removed in step 5 onto the

damper shaft. Squeeze the shims and center the shim stack on top of

the main piston.

If desired, install a new piston tune. Refer to the RockShox spare parts

catalog on

www.sram.com

.

Be sure to keep the main piston assembly parts in the same order.

NOTICE

If the shims are not centered and in the correct order, the shock will not

perform properly.

8

9

10

11

«
...
37
38
39
40
41
...
»

Summary of Contents for RockShox Deluxe RLR



























































Reviews:

No comments