SportsPlay Quick Ship 3 Modified Installation Instructions Manual Download Page 84 | Manualshive

Page: 84 / 140

background image

May 1, 2014

5

922-112 BUBBLE WINDOW
INSTALLATION INSTRUCTION

INSTALLATION STEPS CONTINUED

__5)

Secure the Bubble Window to the Attachment Bracket:

Install and tighten the

3/8” x 3/8” Set Screw (5) in the Four-Hole

Bracket. (See detail A)

__6)

Center the Bubble Window Panel:

You will now need to

center the Bubble Window between the posts. Measure from each
of the posts that the Bubble Window is connected to; make the
measurement the same on each side. Now you can slide the
aluminum collar over to the Bubble Window and secure it to the
pipe with the 1/8” set screw that was installed at the factory.

__7)

Inspect the components:

for sharp edges and if necessary file

them down and apply touch up paint

«
...
82
83
84
85
86
...
»

Summary of Contents for Quick Ship 3 Modified













































































































































Reviews:

No comments

Related manuals for Quick Ship 3 Modified

Brand: FENDT Pages: 31

Brand: UNIA Pages: 62

Brand: Keithley Pages: 67

Brand: Keithley Pages: 23

Brand: Keithley Pages: 93

Brand: Hagie Pages: 141

Brand: Landoll Pages: 70

Brand: U-Line Pages: 9

Green Machine H-3518

Brand: U-Line Pages: 3

Brand: Ultratune Pages: 12

Brand: KUHN Pages: 112

Brand: stilum Pages: 3

Alcotest 7410 GLC

Brand: Dräger Pages: 15

Brand: Audio Precision Pages: 76

Brand: Eco Stage Pages: 17

Brand: D.W. Fearn Pages: 23

Brand: Griven Pages: 16

Brand: Stocks AG Pages: 22

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands