SportsPlay Quick Ship 3 Modified Installation Instructions Manual Download Page 27 | Manualshive

Page: 27 / 140

background image

Value Series

Installation Guide

2/28/11 V-C_OUTLINE.V1.0211

20

Other Installation Tips

•

When attaching a deck to a post

sometimes the factory installed nuts

will spin when tightening the bolt. If this happens simply slide a slim
flathead screw driver in between the deck and the post and slightly pry
on the installed nut to keep it from spinning.

•

If you are mocking up components with the intention of removing
the hardware at some point

, you may want to apply lubricating oil to

the hardware. Stainless steel hardware has a tendency to seize so if you
are planning on removing the hardware you may want to apply lubricant
to prevent this.

•

Pre-drill the holes for the four hole bracket

in the posts with the #7

drill bit included with the hardware

•

Unless specified in the specific component instruction step,

do not

tighten the hardware completely

until the entire unit is assembled.

«
...
25
26
27
28
29
...
»

Summary of Contents for Quick Ship 3 Modified













































































































































Reviews:

No comments

Related manuals for Quick Ship 3 Modified

Brand: IDEAL Networks Pages: 60

Brand: Quivogne Pages: 13

Brand: FoodMarble Pages: 44

Brand: ISA Pages: 24

Ti-Max NLX nano

Brand: NSK Pages: 38

Brand: RAK Pages: 50

HayBoss G2 600A

Brand: Harvest TEC Pages: 20

Brand: 4 Happy Kids Pages: 12

Brand: ELAN Lighting Pages: 10

Fake Plastic Trees

Brand: AUDIO KITCHEN Pages: 8

Brand: Cyclops Lighting Pages: 11

Brand: Eliminator Lighting Pages: 12

Brand: S&S Northern Pages: 6

MASTER PROBLAST 3

Brand: Vaniman Pages: 10

Brand: EDELRID Pages: 8

Brand: Innotech Pages: 5

Brand: Landoll Pages: 64

Brand: Bacharach Pages: 64

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands