SportsPlay Quick Ship 3 Modified Installation Instructions Manual Download Page 116

Page: 116 / 140

February 17, 2010

LABEL MAINTENANCE

Replacement Parts

Contact your distributor to order new
labels. If unable to contact distributor
please call SportsPlay Equipment for
replacements: 1-314-389-4140

Inspect all four labels at all locations
for the following:

•

The labels are present

•

The labels are not worn

•

There are Manufactures id, age
group and warning labels (labels
1-3 on the drawing to the right)
on all four sides at eye level.

•

Each post shall have a surfacing
level label (label 4 on the
drawing) at the proper position on
the post

•

If any of the labels are worn or
missing order replacements

Installing new labels

•

Clean the surface where the
label is being applied

•

Allow surface to dry

•

Apply label

•

Use the label backing material to
smooth out all wrinkles and
bubbles

Summary of Contents for Quick Ship 3 Modified













































































































































Search results

Summary of Contents for Quick Ship 3 Modified

Reviews:

Related manuals for Quick Ship 3 Modified

Brands by name

Popular brands

SportsPlay Quick Ship 3 Modified, Installation Instructions Manual

Search results

Summary of Contents for Quick Ship 3 Modified

Reviews:

Related manuals for Quick Ship 3 Modified

Brands by name

Popular brands