SportsPlay Quick Ship 3 Modified Installation Instructions Manual Download Page 25

Page: 25 / 140

Value Series

Installation Guide

2/28/11 V-C_OUTLINE.V1.0211

Four Hole Bracket & Panel Bracket Installation

Tip for installation

•

Use the #7 drill bit to pre-drill all holes when connecting the bracket
to the post if you are having trouble with the self-tapping screws

Installation

•

Always install the brackets with the set screw facing down (refer to
the drawing on the right)

•

Always install the rubber gasket with the brackets

•

After you have installed the brackets and the component completely
verify the set screw is tightly in place and smooth out all sharp
edges and points

•

Use the screw bit included with the hardware

•

Do not over tighten screws

Set screw facing
down

PANEL
BRACKET

FOUR HOLE
ATTACHMENT
BRACKET

Summary of Contents for Quick Ship 3 Modified













































































































































Search results

Summary of Contents for Quick Ship 3 Modified

Reviews:

Related manuals for Quick Ship 3 Modified

Brands by name

Popular brands

SportsPlay Quick Ship 3 Modified, Installation Instructions Manual

Search results

Summary of Contents for Quick Ship 3 Modified

Reviews:

Related manuals for Quick Ship 3 Modified

Brands by name

Popular brands