SportsPlay Quick Ship 3 Modified Installation Instructions Manual Download Page 101

Page: 101 / 140

April 30, 2014

912-275 PYRAMID ROOF

INSTALLATION INSTRUCTION

BEFORE YOU BEGIN

In addition to the components on the packing list you will need a
drill and 3/4” drill bit, tape measure, marker, and a ladder.

INSTALLATION STEPS

__1)

Review all instructions before beginning:

__2)

Unpack, organize, and identify all components:

Be sure to

place all painted components on a protective surface (cardboard,
cloth, etc…) to prevent damage.

__3)

Locate placement of the Pyramid Roof:

See top down view

of your instruction booklet.

__4)

Temporarily set the Roof Brackets and Pyramid Roof in

place:

You will need to set each of the four Roof Brackets (2) on

the posts that will support the Pyramid Roof. The rounded side of
the Roof Bracket will face to the inside of the deck.

Do not

permanetaly attach them at this time.

Now you can set the Pyramid

Roof onto the Roof Brackets. (See detail A)

__5)

Center the Pyramid Roof:

Measure from each edge of the

four Roof Brackets to the edge of the Pyramid Roof to center the
Pyramid Roof over the deck. Mark the eight holes in the four Roof
Brackets.

Summary of Contents for Quick Ship 3 Modified













































































































































Search results

Summary of Contents for Quick Ship 3 Modified

Reviews:

Related manuals for Quick Ship 3 Modified

Brands by name

Popular brands

SportsPlay Quick Ship 3 Modified, Installation Instructions Manual

Search results

Summary of Contents for Quick Ship 3 Modified

Reviews:

Related manuals for Quick Ship 3 Modified

Brands by name

Popular brands