Spokey 84712, Manual

Page: 7 / 40

6
Belt tracking adjustment (picture, p. 32)
This treadmill is designed to keep the belt reasonably centred while in
use. It is normal for some belts to drift near one side while the belt is
running with no one on it. After a few minutes of use, the belt should have
a tendency to centre itself. If during use, the belt continues to move
toward one side, adjustments are necessary. The procedures are as
below:
▲ First set speed at lowest position.
▲ Second check the belt shifts to which side. If the belt shifts to right, tighten the right bolt and loosen the left bolt by
using 6mm Hexagonal Wrench, until the belt is centered itself; if belt shifts
to left, tighten the left bolt and loosen the right bolt by using 6mm
Hexagonal Wrench, until the belt is centered. When adjusting the belt
using the 6 mm Hexagonal Wrenches, it is important to adjust the belt in
half turn increments. Over adjusting the belt can cause damage to the
mat.
Incline feature

Incline may be adjusted anytime after belt movement.

The incline range is from 0 to 12%.
 Press the following buttons: „LOW”- low (5 %), „MID”- medium (8 %),
„HIGH” – high (12 %) in order to quickly set the appropriate angle of
incline of the running belt.

You can also adjust the
incline percent by using the ‘  ’ or ‘  ’ on
handrail.

The display will indicate incline percent as adjustments are made.

Incline will remain in its position when display is turned off.
HOW TO CHECK THE RUNNING MAT FOR PROPER LUBRICATION (picture, p. 32)

Disconnect the main power supply.

Fold the treadmill up into the storage position.

Feel the back surface of the running mat.
SAFETY KEY
A safety key is provided with this machine. Remove the safety key will
stop the walking belt immediately; the treadmill will shut off automatically. Insert the safety key will reset the display. Use only in urgent situations
MAINTANCE
Caution: before cleaning / lubrication you must take out the power plug
from a socket.
For cleaning the exercise machine, do not use any abrasive detergents.
Use a soft, damp cloth to remove dirt and dust.
The monitor (power supply dome) should be cleaned only with a dry cloth.
The equipment should be stored in dry places in order to protect it from
any moisture and corrosion.
Use a soft, damp cloth to wipe off the edges of the treadmill belt, and the
space between the treadmill belt and the frame edges. Clean the edge of
the belt on its bottom side also. Clean the upper part of the belt with a
brush and soap water once a month. NOTE: Before you start using the treadmill again, wait until the equipment
is completely dry.
Vacuum under the equipment at least once a month to prevent dust from
accumulating.
Once a year, it is recommended to remove the black cover of the engine
in order to remove any dust that may accumulate there.
NOTE: The level of equipment operational safety can be maintained only
by regular inspections checking for any damage and wear.
Connecting elements are the most vulnerable to any wear..
Belt/deck/roller lubrication
The mat/deck friction may play a major role in the function and life of your
treadmill and that is why we recommend you constantly lubricate this
friction point to prolong the life time of your treadmill.
You should apply the lubrication after approximately the first 20 hours of
operation. We recommend lubrication of the deck every 30 days.
See below procedures for lubricating:

Use a soft, dry cloth to wipe the area between the belt and deck.

Spread lubricant onto the inside surface of belt and deck evenly
(make sure the machine is turned off and power is disconnected).

Periodically lubricate the front and rear rollers to keep them at their
peak performance.
If the treadmill belt/deck/roller is kept reasonably clean it is possible to
expect over 120 hours before additional re-lubing is necessary.
HOW TO OPERATE THE COUNTER
Console
“clear” button - In the state of initialization or operation, press it, all the
figures are cleared to zero.
“music” button - Press this button, play music; while press it again, music
stops.
“set” button -In the state of initialization, press it, time, distance, calorie
can be set.
-
Constant running time: less than 1 hour
Parameters: speed, time, incline, distance, heart rate, racetrack and
calories
Getting started
Power the treadmill on by plugging it into an appropriate wall outlet, then
turn on the power switch located at the front of the treadmill below the
motor shield. Ensure that the safety key is installed, as the treadmill will
not power on without it. When the power is turned on, all the lights on the
display will light for a short time.
Note: When running, make sure the plastic clip is fastened on your
clothing. It is for your safety, should you fall or move too far back on the
treadmill..
start/stop
Speed
3, 6, 9 km/h
clear/reset
music
mode
set
safety key
Incline
“+/-“:
Each press:
+/- 1 %
Incline
3, 6, 9 %
Speed
“+ / -“:
Each press:
+/- 0,1 km/h