Spacelabs Healthcare elance 5 Service Manual Download Page 19

Page: 19 / 94

Theory

Invasive Blood Pressure Block Diagram

Patient blood pressure detection is by pressure transducer connected to the patient blood vessel via

catheter or tubing.

A +5v excitation voltage is applied to the pressure transducer. The output of the pressure

transducer is at 5uv/mmHg/V.

Blood pressure signal is converted to voltage by the pressure transducer and sent through the filter

to the amplifier.

Calibration signal is control by a multiplexer for calibrating BP1 and BP2 channels.

Amplified signal is sent to the analog to digital converter for conversion.

Digitized signal is sent to the microcontroller for processing.

Temperature Block Diagram

Patient temperature detection is by using a temperature probe. The thermistor inside the

temperature probes varies according to the temperature changes.

The thermistor signal is sent through a filter to the amplifier. Then sent to the A/D for

conversion. Digitized signal is sent to the microcontroller for processing.

A 20°c and 40°c signal controlled by the ATMEGA162V is used for auto calibration of the

temperature channels.

3-3

Filter

AMP

A/D

Converter

Calibration

MUX

IBP1
Input

AMP

A/D

Converter

Filter

IBP2
Input

Filter

AMP

A/D

Converter

Auto CAL

°C

/40

°C

T1/T2
Input

Summary of Contents for elance 5































































































Search results

Summary of Contents for elance 5

Reviews:

Brands by name

Popular brands

Spacelabs Healthcare elance 5, Service Manual

Search results

Summary of Contents for elance 5

Reviews:

Brands by name

Popular brands