SONIX SN8P2977 User Manual Download Page 74

Page: 74 / 146

SN8P2977

8-Bit Micro-Controller with Regulator, PGIA, 24-bit ADC

SONiX TECHNOLOGY CO., LTD

Page 74

Version 1.7

JMP

EXIT_CKTT0CVAL:

; If FC = 1, jmp EXIT_CKTT0CVAL

B0BSET

T0IRQFLAG

; Set T0IRQFLAG (T0C counts overflow.).

EXIT_CKTT0CVAL:

MOV

A, NEWT0C

MOV

OLDT0C, A

; Update T0C value

RET

; Exit sub-routing.



CKT_T0FLAG sub-routing (Check T0 timer overflow flag).

CKT_T0FLAG:

B0BTS1

T0IRQFLAG

; Check T0IRQ status.

JMP

EXIT_CKTT0FLAG

; Jmp EXIT_CKTT0FLAG.

B0BCLR

T0IRQFLAG

; Clear T0IRQFLAG.

CALL

DELAY

; Call delay time = over 1/32.768ms (for RTC limit).

B0BCLR

FT0IRQ

; Clear FT0IRQ.

CALL

UPDATE_TIME

; Update time.

EXIT_CKTT0FLAG:

RET

; Exit sub-routing.



Into green mode before.

CALL

CKT_T0CVAL

; Check T0C value overflow

CALL

CKT_T0FLAG

; Check T0C overflow Flag and update time.



Process green mode after wakeup.

INTO_GREENMODE: .

B0BCLR

FCPUM0

B0BSET

FCPUM1

; Into green mode

WAKEUP:

B0BTS1

FT0IRQ

; Check FT0IRQ

JMP

CKT_OTHER

; Check other trigger wakeup source.

CALL

DELAY

; Call delay time = over 1/32.768ms (for RTC limit).

CLR

T0FLAG

; Clear T0FLAG.

B0BCLR

FT0IRQ

; Clear FT0IRQ.

MOV

A, T0C

MOV

OLDT0C, A

; Update T0C value

CALL

UPDATE_TIME

; Update time.

CKT_OTHER:

Summary of Contents for SN8P2977



















































































































































Search results

Summary of Contents for SN8P2977

Reviews:

Related manuals for SN8P2977

Brands by name

Popular brands

SONIX SN8P2977, User Manual

Search results

Summary of Contents for SN8P2977

Reviews:

Related manuals for SN8P2977

Brands by name

Popular brands