SONIX SN8P2977 User Manual Download Page 2 | Manualshive

Page: 2 / 146

background image

SN8P2977

8-Bit Micro-Controller with Regulator, PGIA, 24-bit ADC

SONiX TECHNOLOGY CO., LTD

Page 2

V1.7

AMENDENT HISTORY

Version

Date

Description

Ver1.0

2016.12

New Version start.

Ver1.1

2017.01

Modify BZRM & ROMDAH & ROMDAL register only write.

Ver1.2

2017.01

1.

Modify 1.2

MIGRATION TABLEUART Total Capacitors descriptions.

2. Modify 1.1 SELECTION TABLE descriptions.
3.

Modify 1.6 PIN DESCRIPTIONS descriptions.

4. Modify 2.1.3 CODE OPTION TABLE Low_power descriptions.
5. Modify 2.1.5.3 BIT DEFINITION of SYSTEM REGISTER descriptions.
6. Modify 5.1 Operating mode description.
7. Modify 11.5 C-TYPE LCD DRIVER MODE description.
8. Modify 12.1 ROMADRH/ROMADRL REGISTER description.
9. Modify 13 Regulator, PGIA and ADC description.
10. Add

AMPCKS[2:0]: PGIA chopper selection.(Always set “7.8k Hz”) description.

11. Add 13.4.2 AMPM- Amplifier Mode Control Register Note_2: When PGIA Gain set 1x
(GS[2:0]=111) application, the AI+/AI- signal input buffer of PGIA mustbe enabled
(AMPENB=1) for input high impedance characteristic of ADC.
12. Modify 13.5 Temperature Sensor (TS) description.
13. Modify 13.6 24-Bit Analog to Digital Converter (ADC) description.
14. Modify 13.6.5 ADCM1- ADC Mode1 Register Bit 0 ADCENB description.
15. Modify 13.6.7 ADC Data Register Note description.
16. Modify 14 APPLICATION CIRCUIT.
17. Modify 17 ELECTRICAL CHARACTERISTIC.

Ver1.3

2017.02

1.

Modify 13.4.1 CHS- Analog input signal channel selection Register note 4.

(GS[2:0]=000)
2. Modify 13.4.2 AMPM- Amplifier Mode Control Register note1 & note2. (GS[2:0]=000)
3. Modify 12.2 ROMADRH/ROMADRL REGISTER

Ver1.4

2017.02

1. Add

ROMADR[15] : ISP ROM Programming selection control bit. (Always set “0”)

2. Modify ROMADR[11:0] : ISP ROM Programming Address.
3.

Modify ELECTRICAL CHARACTERISTIC P0 IoH Min value 7mA.

4. Modify ELECTRICAL CHARACTERISTIC P1 IoH Min value 15mA,Typ value 20mA
5. Modify ELECTRICAL CHARACTERISTIC P3 IoH Min value 12mA.
6. Modify ELECTRICAL CHARACTERISTIC P2 IoL Min value 45mA,Typ value 60mA
7. ADD ELECTRICAL CHARACTERISTIC P1,P3 IoL Min value 45mA
8. ADD ELECTRICAL CHARACTERISTIC LBT 3.0V Min = 2.8V,Typ=3.0V,Max=3.2V
9. ADD ELECTRICAL CHARACTERISTIC LBT 3.6V Min = 3.4V,Typ=3.6V,Max=3.8V

Ver1.5

2017.06

Add package information(QFN32

、

TSSOP28

、

SSOP20

、

SOP16)

Ver1.6

2017.09

1.Modify the ceramic capacitor configuration of the application circuit.(page125,126)
2.Modify QFN32 symbols table.(A Typical

→

0.8mm, A Max

→

0.9mm)(page 139)

3.Add Package information(Ver1.5) to FEATURES(Chapter 1.3)
4.Modify QFN32 package type of name to 2975 from 2977.(page 14)

Ver1.7

2017.09

1.Modify the name of package type in SSOP20 from SN8P2972 to SN8P2973.(page14)

«
1
2
3
4
...
»

Summary of Contents for SN8P2977



















































































































































Reviews:

No comments

Related manuals for SN8P2977

Brand: Vega Pages: 20

Brand: Zaiput Flow Technologies Pages: 10

Brand: W.E.ST. Pages: 34

Brand: Ltech Pages: 4

Brand: Motor Guard Pages: 2

Ratio Feeder J+ Advanced Series

Brand: H.E. Anderson Pages: 11

Synergy SGY-101

Brand: Fairford Pages: 20

Brand: ST Pages: 40

Brand: Varian Pages: 37

Brand: Midian Electronics Pages: 22

Brand: TAC Vista Pages: 2

Brand: Ellard Pages: 21

Brand: Altera Pages: 59

Brand: A.O. Smith Pages: 46

Brand: Phocos Pages: 2

EscapeKeeper JR

Brand: Fright Ideas Pages: 2

Brand: Vent-Axia Pages: 4

komplete kontrol s series

Brand: Native Instruments Pages: 338

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands