SONIX SN8P2977 User Manual Download Page 77

Page: 77 / 146

SN8P2977

8-Bit Micro-Controller with Regulator, PGIA, 24-bit ADC

SONiX TECHNOLOGY CO., LTD

Page 77

Version 1.7

8.3.3

TC0X8, TC0GN FLAGS

0D8H

Bit 7

Bit 6

Bit 5

Bit 4

Bit 3

Bit 2

Bit 1

Bit 0

T0M

T0ENB

T0rate2

T0rate1

T0rate0

TC0X8

TC0GN

T0TB

Read/Write

R/W

After reset

Bit 0

T0TB:

RTC clock source control bit.

0 = Disable RTC (T0 clock source from Fcpu).
1 = Enable RTC.

Bit 1

TC0GN:

Enable TC0 Green mode wake up function

0 = Disable.
1 = Enable.

Bit 2

TC0X8:

TC0 internal clock source control bit.

0 = TC0 internal clock source is Fcpu. TC0RATE is from Fcpu/2~Fcpu/256.
1 = TC0 internal clock source is Fosc. TC0RATE is from Fosc/1~Fosc/128.

Bit [6:4]

T0RATE[2:0]:

T0 internal clock select bits.

000 = fcpu/256.
001 = fcpu/128.

…

110 = fcpu/4.
111 = fcpu/2.

Bit 7

T0ENB:

T0 counter control bit.

0 = Disable T0 timer.
1 = Enable T0 timer.



Note: Under TC0 event counter mode (TC0CKS=1), TC0X8 bit and TC0RATE are useless.

Summary of Contents for SN8P2977



















































































































































Search results

Summary of Contents for SN8P2977

Reviews:

Related manuals for SN8P2977

Brands by name

Popular brands

SONIX SN8P2977, User Manual

Search results

Summary of Contents for SN8P2977

Reviews:

Related manuals for SN8P2977

Brands by name

Popular brands