Smiths BOEING B737-100 Maintenance Manual Supplement Download Page 40

Page: 40 / 146

Smiths Aerospace

Electronic Systems – Malvern

DOC NO.0134ED

MAINTENANCE MANUAL SUPPLEMENT

BOEING B737-100/200/300/400/500

28-41-04

Measure resistance from
Comp Lo-Z to Hi-Z at the

indicator connector

Clear FQI errors and

confirm error persists

Repair A/C harness

(WDM 28-41-01)

<500 megohm

>500 megohm

Remove TSU from Tank wall.

(AMM 28-41-04/401)

Repair/Replace tank harness

and/or compensator

(AMM 28-41-44/401)
(AMM 28-41-21/401)

<500 megohm

>500 megohm

Replace TSU

(AMM 28-41-04/401)

Drain sump to remove

water from tank

(AMM 28-41-21/501)

Return to service

Error cleared

Error persists

Remove master indicator.

Disconnect A/C Harness from TSU

(AMM 28-41-04/401)

Measure resistance from Comp

Lo-Z to Hi-Z at tank wall

Operational Test

(AMM 28-41-04/501)

Err 3: Compensator Leakage

Figure 104

EFFECTIVITY

Page 116

April 19/02

Airplanes with Smiths 2307 Model Fuel Quantity
Indicators with TSU

Summary of Contents for BOEING B737-100



















































































































































Search results

Summary of Contents for BOEING B737-100

Reviews:

Related manuals for BOEING B737-100

Brands by name

Popular brands

Smiths BOEING B737-100, Maintenance Manual Supplement

Search results

Summary of Contents for BOEING B737-100

Reviews:

Related manuals for BOEING B737-100

Brands by name

Popular brands