Smiths BOEING B737-100 Maintenance Manual Supplement Download Page 32

Page: 32 / 146

Smiths Aerospace

Electronic Systems – Malvern

DOC NO.0134ED

MAINTENANCE MANUAL SUPPLEMENT

BOEING B737-100/200/300/400/500

28-41-04

Read the total fuel quantity from the PDCS CDU.

1. Turn the CDU Mode Selector switch to STBY.

2. Depress the recall key.

3. Depress the minus key.

4. Depress the page advance key.

The total fuel quantity shown must be equal to the total of all the fuel quantity indicators with a
tolerance of +/- 100 pounds (+/- 50 kilograms).

IF -

RCL

-----

Total fuel quantity is not equal to the total of all the
fuel quantity indicators with a tolerance of +/- 100
pounds (+/- 50 kilograms) – FIG. 115

NOT OK

CONTINUE ON SHEET 6 FOR 2101 REFUEL INDICATOR

SHEET 7 FOR 2120 REFUEL INDICATOR

Troubleshooting for the Fuel Quantity Indicating System - WITH PDCS

Figure 101 (Sheet 5)

Page 109

Dec 18/02

Airplanes with Smiths 2307 Model Fuel Quantity
Indicators with TSU

EFFECTIVITY

Summary of Contents for BOEING B737-100



















































































































































Search results

Summary of Contents for BOEING B737-100

Reviews:

Related manuals for BOEING B737-100

Brands by name

Popular brands

Smiths BOEING B737-100, Maintenance Manual Supplement

Search results

Summary of Contents for BOEING B737-100

Reviews:

Related manuals for BOEING B737-100

Brands by name

Popular brands