Silverline 938778 Manual Download

Page: 13 / 66

18V Mini Circular Saw 115mm

silverlinetools.com

Making a cut

WARNING:

Use ONLY enough pressure to keep the saw cutting. NEVER force the saw; allow the

Blade (19) and the saw to do the work. Use of excessive pressure that causes bending or twisting of

the Blade may cause the Blade to break.
1. Hold the saw securely and rest the front edge of the Base Plate (13) on the edge of the workpiece

(Fig. VII (a))

2.  Check that the Blade is not in contact with the workpiece, or any other object
3.  Switch the tool ON and allow to reach full speed
4.  Retract the Blade Guard (16) (Fig. VII (b)) just enough to allow the blade to engage with the

workpiece

5.  Move the saw forward until the blade starts cutting, then release the Blade Guard
6.  Push the saw smoothly forward, across the workpiece (Fig. VII (c))
7.  Maintain a steady movement and keep the Base Plate pressed against the workpiece

NOTE:

The front edge of the Base Plate features a Guide Notch (21). For normal cutting align the

notch marked ‘0˚’ with the intended cutting line; for 45˚ bevel cutting align the notch marked ‘45˚’

with the cutting line.
8. Allow the Blade to pass through the material and release the ON/OFF Switch (12).

WARNING:

If the cut does not reach the edge of the workpiece, release the ON/OFF Switch and

allow the Blade to stop moving before lifting out of the cut.

WARNING:

Remove the Battery (10) and Blade when the tool is to be left unattended.

Making a plunge cut

WARNING:

Plunge cutting is an advanced technique with higher risk. Only attempt plunge

cuts when you are competent and experienced with this technique. These instructions are given

as a guide only.

WARNING:

ONLY attempt the plunge cutting procedure in soft materials such as wood,

plasterboard and similar materials. DO NOT attempt plunge cuts in metal or hard materials. ONLY

use blades specifically designed for plunge cutting. If in doubt, refer to the blade manufacturer’s

instructions.

WARNING:

Inspect both sides of the surface you are planning on plunge cutting into. Ensure

there are no foreign objects on the underneath, or objects that could be damaged. Be aware of

hidden pipework and cables when plunge cutting into drywalls, ceilings or floorboards. If pipes or

cables may be present, switch OFF all electrical circuit breakers and shut off water and gas supplies

at the relevant mains valves.

WARNING:

Blindly plunge cutting into walls, floors and ceilings may lead to serious injury and

substantial property damage.
1.  Mark out the cutting line
2.  Adjust the Base Plate (13) to the required depth
3.  Position the front of the Base Plate on the workpiece so that the Blade (19) is in-line with the

cutting line (Fig.VIII (a))

4.  Ensure the Blade is clear of the workpiece
5.  Hold the tool securely, ensuring you always have full control
6.  Switch the tool ON and allow the Blade to reach full speed
7.  Adjust the Blade Guard (16) to enable the Blade to contact the workpiece (Fig. VIII (b))
8.  Pivot the saw on the tip of the Base Plate until the Blade contacts the workpiece (Fig. VIII (c))
9.  Release the Blade Guard
10. Continue to pivot slowly, until the Blade has fully penetrated the thickness of the workpiece
11. Once the face of the Base Plate is flat against the workpiece, continue to make the cut

Using the laser

The Laser (3) indicates the position of the cut by projecting a bright red line onto the workpiece.

Keeping the laser light in-line with the cut mark will ensure an accurate cut.
1.  Mark up the workpiece to be cut
2.  Switch ON the Laser using the Laser ON/OFF Switch (5)
3.  Align the Laser beam with the cut mark (Fig. VII (d))
4.  Make the cut, keeping the Laser beam in-line with the cut mark
5.  Turn the Laser OFF

Accessories

• A full range of accessories including circular saw blades, straight edges and rip-cut guides, is

available from your Silverline stockist

• Spare parts can be obtained from toolsparesonline.com

Maintenance

WARNING:

Always disconnect the tool from the power supply, before cleaning or carrying out

maintenance.

General inspection

• Regularly check that all the fixing screws are tight. They may vibrate loose over time
• Repairs should be carried out by an authorised Silverline service centre.

Lubrication

• Lubricate all moving parts with a suitable lubricant spray, at regular intervals

Cleaning

WARNING:

ALWAYS wear protective equipment including eye protection and gloves when

cleaning this tool.
• Keep your tool clean at all times. Dirt and dust will cause internal parts to wear quickly, and

shorten the device’s service life

• Clean the body of your tool with a soft brush, or dry cloth
• Never use caustic agents to clean plastic parts. If dry cleaning is not sufficient, a mild detergent

on a damp cloth is recommended

•  Water must never come into contact with the tool
•  Ensure the tool is thoroughly dry before using it
•  If available, use clean, dry, compressed air to blow through the ventilation holes (where

applicable)

Brushes

•  Over time the carbon brushes inside the motor may become worn
•  Excessively worn brushes may cause loss of power, intermittent failure, or visible sparking
•  If you suspect that the brushes may be worn, have them replaced at an authorised service centre

Contact

For technical or repair service advice, please contact the helpline on (+44) 1935 382 222

Web:

silverlinetools.com/en-GB/Support

UK Address:

Toolstream Ltd.
Boundary Way
Lufton Trading Estate
Yeovil, Somerset
BA22 8HZ, United Kingdom

Storage

• Store this tool carefully in a secure, dry place out of the reach of children
• For long-term storage, remove batteries and store separately

Disposal

Li-ion batteries should not be disposed of with household waste. If you do not know of a li-ion

battery recycling centre in your area, contact your local authority or original dealer for advice on

disposal of li-ion batteries.
Always adhere to national regulations when disposing of power tools that are no longer functional