![background image](http://html1.mh-extra.com/html/silverline/278581/278581_manual_1273349009.webp)
www.silverlinetools.com
9
1050W Angle Grinder 125mm
278581
• Hold the machine appropriately to ensure that debris produced does not land on
skin or clothing
• Do not touch the spindle lock button while the tool is operating
• A grinding disc will gradually wear down during use, reducing its size.
If a disc
becomes too small to work with easily, stop using it and replace it with a new disc
Additional Safety For Super Abrasives
• Superabrasives are generally inflexible and could shatter, so must be handled
with the utmost care.
Damaged or improperly mounted superabrasives are
dangerous and can cause SEVERE injury to the user and other people in the vicinity
• Types of superabrasive wheels include diamond cutting discs, welded
metal discs, CBN discs etc.
Choose your superabrasive tool carefully, taking into
consideration the workpiece material, the machine dimensions and capabilities.
Make sure the machine does not exceed the maximum operating speed of the
superabrasive disc
• NEVER use superabrasive cutting discs for side grinding, as this might lead to
the disc shattering
• Superabrasive wheels have to be carefully inspected and tested before
mounting.
Metal wheels should be subjected to a sound test: hold the wheel on a
mandrel or with a finger inserted through the bore, then tap it with a non-metallic
object at several points and listen each time to the sound produced. An intact wheel
will produce a clear ‘bell like’ metallic sound. Damaged wheels will give a dull,
chattering sound. If in doubt, DO NOT USE, MARK AS DAMAGED AND DISCARD
• Make sure the machine’s mounting flange is compatible with the
superabrasive wheel.
Refer to the manufacturer’s mounting instructions
• ALWAYS conduct a test run after mounting, with no load for at least 30
seconds, to determine if the wheel runs balanced and does not produce
excessive vibration.
If it does, switch off IMMEDIATELY, remove the disc, inspect,
re-mount and re-test if no damage is detected
• If planning on using the superabrasive wheel with a coolant, liquid dust
suppressant or lubricant, first check if the wheel, machine and workpiece are
compatible with wet cutting and with the compound to be used.
Always apply
liquid to an already running wheel, never to a non-moving tool, as the unbalance
could lead to the rupture of the wheel. When switching off, remove the liquid supply
first and let the machine run at no-load, until centrifugal forces have drained all
liquid from the wheel. Dry off the wheel after use, and prevent liquid from being
absorbed into the wheel
1
Auxiliary Handle
2
Handle Thread (Right)
3
Handle Thread (Top)
4
Handle Thread (Left)
5
Motor Vents
6
Resting Foot
7
Main Handle
8
Lock Off Button
9
On/Off Trigger Switch
10 Grinding Guard
11 Disc (not included)
12 Guard Collar
13 Spindle Lock
14 Pin Spanner
15 Inner Flange
16 Outer Flange
17 Spindle
18 Cutting Wheel Guard
Product Familiarisation
Intended Use
Angle grinder suitable for light to medium duty grinding of metal and other materials with
a fitted disc of the correct type. Suitable for cutting various materials when fitted with the
supplied cutting guard. Also suitable for wire brushing and sanding applications with the
optional purchases of compatible accessories.
Unpacking your Tool
Carefully unpack and inspect your tool. Familiarise yourself with all its features
and functions.
Ensure that all parts of the tool are present and in good condition. If any parts are missing
or damaged, have such parts replaced before attempting to use this tool.
Before Use
WARNING
: Always unplug the grinder from the mains supply before attempting to fit or
replace any attachment. Never fit any attachment with a maximum speed lower than the
no load speed of the machine.
All discs and accessories must be subjected to a visual inspection prior to installation,
to ensure they are in good condition and within their expiry date. If in doubt, DO NOT
USE AND DISCARD
• Always check all parts and attachments are secure, and that rotating parts will not foul
on guards or machine case
• Always hold the machine, using both hands, by the handles provided
• Be aware that the cast metal gear housing may get hot during use
• Hot air will be emitted from the ventilation holes
• Ensure that the ventilation holes are not obscured in any way
• Always wear appropriate personal protective equipment for the task. Use of this
machine requires ear defenders, eye protection, gloves, breathing protection, and if
appropriate a hard hat
Fitting the auxiliary handle
WARNING
: To ensure operator safety, ALWAYS use the auxiliary handle. Install it at the most
appropriate position for the individual task.
1. Screw the Auxiliary Handle (1) clockwise into one of the Auxiliary Handle Threads (2, 3
or 4) of the tool. Tighten by hand
2. To remove the Auxiliary Handle, unscrew anti-clockwise
WARNING
: The correct guard MUST be installed for each application before
operation commences.
WARNING
: NEVER install a cutting disc or superabrasive cutting wheel without the Cutting
Wheel Guard (19) in place.
Note
: The guard must be adjusted so that it is situated between the disc and the
operator. Reset the guard if the work angle or the position of the operator changes. Seek
professional guidance if you are unsure how to operate the guards or any other safety
features of the machine correctly.
Note
: The angle grinder is supplied with the Grinding Guard (10) pre-installed.
Adjusting the guard
1. Loosen the guard securing bolt of the Guard Collar (12)
2. The guard – either Grinding Guard (10) or Cutting Wheel Guard (18) - can be moved
through a range of approximately 90°, so that it can be placed between the Disc (11)
and the operator at any required work angle
3. Tighten the bolt or lever
Removing Guard
Note
: Skip Step 1 if no disc is installed.
1. Depress the Spindle Lock button (13), rotate the Spindle (17) until you feel the lock
engage, use the Pin Spanner (14) to remove the Outer Flange (16) and remove the disc
2. Loosen the guard securing bolt of the Guard Collar (12) and rotate the guard – either
Grinding Guard (10) or Cutting Wheel Guard (18) - until the protrusions on the band of
the guard are aligned with the notches on the gear housing, and remove the guard
Installing Guard
1. Loosen the guard securing bolt of the Guard Collar (12)
2. Align the protrusions on the wheel guard band with the notches on the gear housing
3. Push the guard – either Grinding Guard (10) or Cutting Wheel Guard (18) - onto the gear
housing and adjust position
4. Tighten the securing bolt
278581_Z1MANPRO1.indd 9
18/05/2016 12:40