Silicon Laboratories EMBER EM358 series Reference Manual Download Page 94

Page: 94 / 257

EM358x

Rev. 0.4

8.5.5

Registers

Refer to Registers (in the SPI Master Mode section) for a description of the SCx_DATA, SCx_RATELIN, and

SCx_RATEEXP registers.

SCx_TWISTAT

SC1_TWISTAT

TWI Status Register

Address: 0x4000C844 Reset: 0x0

SC2_TWISTAT

TWI Status Register

Address: 0x4000C044 Reset: 0x0

SC_TWICMDFIN SC_TWIRXFIN SC_TWITXFIN SC_TWIRXNAK

Bitname

Bitfield

Access Description

SC_TWICMDFIN

[3]

This bit is set when a START or STOP command completes. It clears on

the next TWI bus activity.

SC_TWIRXFIN

[2]

This bit is set when a byte is received. It clears on the next TWI bus

activity.

SC_TWITXFIN

[1]

This bit is set when a byte is transmitted. It clears on the next TWI bus

activity.

SC_TWIRXNAK

[0]

This bit is set when a NACK is received from the slave. It clears on the

next TWI bus activity.

Summary of Contents for EMBER EM358 series


































































































































































































































































Search results

Summary of Contents for EMBER EM358 series

Reviews:

Silicon Laboratories EMBER EM358 series, Reference Manual, Page: 94 / 257

Search results

Summary of Contents for EMBER EM358 series

Reviews: