manualshive.com logo in svg

Silicon Laboratories EMBER EM358 series, Reference Manual, Page: 18 / 257

Share
Download
Silicon Laboratories EMBER EM358 series Reference Manual Download Page 18

EM358x 

 

18 

Rev. 0.4 

 

2.3  Memory Protection Unit 

The EM358x includes the ARM

®

 Cortex

TM

-M3 Memory Protection Unit, or MPU. The MPU controls access rights 

and characteristics of up to eight address regions, each of which may be divided into eight equal sub-regions. 

Refer to the ARM

®

 Cortex

TM

-M3 Technical Reference Manual (DDI 0337A) for a detailed description of the MPU. 

Ember software configures the MPU in a standard configuration and application software should not modify it. The 

configuration is designed for optimal detection of illegal instruction or data accesses. If an illegal access is 

attempted, the MPU captures information about the access type, the address being accessed, and the location of 

the offending software. This simplifies software debugging and increases the reliability of deployed devices. As a 

consequence of this MPU configuration, accessing RAM and register bit-band address alias regions is not 

permitted, and generates a bus fault if attempted. 
 
 

Summary of Contents for EMBER EM358 series


































































































































































































































































Reviews:

No comments