Sigma 3-30K Operating Manual Download Page 60

Page: 60 / 100

4-16K

Malfunctions and Error Correction

Version 12/2008, Rev. 1.11 of 27/01/2012

Translation of the original operating manual

6.5 Switching the Centrifuge OFF

Open the centrifuge when it is not in use so moisture can

evaporate. This prevents the increased wear of the motor
bearings.

Press the mains power switch on the front of the right side.

Malfunctions and Error Correction

7.1 General Malfunctions

Malfunctions are indicated by a dialogue box. If the sound signal is
activated, it sounds when the error message is displayed.

Eliminate the source of the problem (see tables in fig. 7.1 and

7.3).

Acknowledge the error messages by pressing the knob.

Only Spincontrol Comfort:

Error messages that are caused by the power circuit board are
marked with a “P” in front of the error code.

Only Spincontrol Professional:

Error messages can be eliminated by pressing the lid key. The error
itself will not be eliminated, but the centrifuge can be operated again.

Type of error

Possible reason

Correction

No power in the mains supply

Check fuse in the mains supply

Power cord is not plugged in

Plug in power cord correctly

Fuses have tripped

Reactivate temerature fuse (see
5.4.1 "Connection")

Mains power switch off

Switch mains power switch on

No indication on the display

Lid is not closed correctly

Close lid.

Centrifuge cannot be started:
Start key LED is not illuminated

Several

Power off/on. If the error occurs
again, contact service

Centrifuge cannot be started:
Lid key LED flashes

The lid lock is not closed
correctly

Open and close lid. If the error
occurs again, contact service

Brief mains power failure

Press start key in order to
restart the centrifuge

Centrifuge decelerates during
operation

System error

Power off/on. If the error occurs
again, contact service

- improper loading
- Centrifuge is inclined
- Drive problem
- centrifuge was moved
during run

Balance loading and restart the
centrifuge. If the error occurs
again, contact service

Centrifuge decelerates during
operation, imbalance dialogue
box is displayed

- ungreased load-bearing bolts

Clean and grease load-bearing
bolts

Summary of Contents for 3-30K





































































































Search results

Summary of Contents for 3-30K

Reviews:

Brands by name

Popular brands

Sigma 3-30K, Operating Manual

Search results

Summary of Contents for 3-30K

Reviews:

Brands by name

Popular brands