manualshive.com logo in svg

Siemens Synova FC330A, Manual

The Siemens Synova FC330A Operating Manual is an essential resource for maximizing the product's potential. With an easy-to-understand layout and comprehensive instructions, this manual is available for free download at manualshive.com. Discover the full capabilities of your Siemens Synova FC330A with this invaluable user manual.

Share
Download
background image

Fire Safety & Security Products

Building Technologies

1583_o_en_−−_8

123

08.2005

8

Maintenance

8.1

General

The fire detection control unit FC330A requires only little maintenance work. It has a high
degree of self monitoring, such as

detectors monitored on presence and wire break/short, series SynoLINE300/600 also
on drift (only OPxxxA and OHxxxA)

call points monitored on broken glass and wire break/short

line to alarm sounders monitored on wire break/short

line to externally located remote transmission device monitored on wire break/short

automatic ’battery load test’ every 24h

permanent system checking by ’watch dog’ function

programmed user function and user texts are stored in a Flash-EPROM

automatic switching of summer- to winter time and vice versa

Alarmcom recommends the following schedule for the system performance checks (see
table below). However, possible local national regulations have priority.

8.2

Recommended system performance checks

ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ

ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ

Performance checks

ÁÁÁÁÁÁÁÁÁ

ÁÁÁÁÁÁÁÁÁ

Interval in years

ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ

ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ

Performance checks

ÁÁÁ

ÁÁÁ

1

ÁÁÁ

ÁÁÁ

2

ÁÁÁ

ÁÁÁ

5

ÁÁÁ

ÁÁÁ

6

ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ

ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ

Alarmorganization

ÁÁÁ

ÁÁÁ

ÁÁÁ

ÁÁÁ

ÁÁÁ

ÁÁÁ

ÁÁÁ

ÁÁÁ

ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ

ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ

− Check the functioning of the delay times ’V1’ and ’V2’

ÁÁÁ

ÁÁÁ

F

ÁÁÁ

ÁÁÁ

ÁÁÁ

ÁÁÁ

ÁÁÁ

ÁÁÁ

ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ

ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ

− Activate automatic detector while system is set to ’unmanned’

ÁÁÁ

ÁÁÁ

F

ÁÁÁ

ÁÁÁ

ÁÁÁ

ÁÁÁ

ÁÁÁ

ÁÁÁ

ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ

ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ

− Activate manual call point

ÁÁÁ

ÁÁÁ

F

ÁÁÁ

ÁÁÁ

ÁÁÁ

ÁÁÁ

ÁÁÁ

ÁÁÁ

ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ

ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ

− Verify switchover ’manned’ to ’unmanned’ and vice versa

ÁÁÁ

ÁÁÁ

F

ÁÁÁ

ÁÁÁ

ÁÁÁ

ÁÁÁ

ÁÁÁ

ÁÁÁ

ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ

ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ

− Check activation of remote transmission equipment

ÁÁÁ

ÁÁÁ

F

ÁÁÁ

ÁÁÁ

ÁÁÁ

ÁÁÁ

ÁÁÁ

ÁÁÁ

ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ

ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ

Alarm sounder

ÁÁÁ

ÁÁÁ

ÁÁÁ

ÁÁÁ

ÁÁÁ

ÁÁÁ

ÁÁÁ

ÁÁÁ

ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ

ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ

− Activate ’horn test’ and check all acoustic alarm devices

ÁÁÁ

ÁÁÁ

F

ÁÁÁ

ÁÁÁ

ÁÁÁ

ÁÁÁ

ÁÁÁ

ÁÁÁ

ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ

ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ

Detector network 

3)

ÁÁÁ

ÁÁÁ

ÁÁÁ

ÁÁÁ

ÁÁÁ

ÁÁÁ

ÁÁÁ

ÁÁÁ

ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ

ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ

− Activate a detector within each line and verify zone assignment and parameters

ÁÁÁ

ÁÁÁ

F

ÁÁÁ

ÁÁÁ

ÁÁÁ

ÁÁÁ

ÁÁÁ

ÁÁÁ

ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ

ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ

− Check all detectors and call points visually

ÁÁÁ

ÁÁÁ

F

ÁÁÁ

ÁÁÁ

ÁÁÁ

ÁÁÁ

ÁÁÁ

ÁÁÁ

ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ

ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ

− Activate all detectors and all call points

ÁÁÁ

ÁÁÁ

ÁÁÁ

ÁÁÁ

F

ÁÁÁ

ÁÁÁ

ÁÁÁ

ÁÁÁ

ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ

ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ

Á

ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ

− Check each detection line whether a short circuit or open line activates fault

a) conventional detector line
b) addressable detector line

ÁÁÁ

ÁÁÁ

ÁÁÁ

ÁÁÁ

ÁÁÁ

ÁÁÁ

ÁÁÁ

ÁÁÁ

ÁÁÁ

F

F

ÁÁÁ

ÁÁÁ

ÁÁÁ

ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ

ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ

Á

Á ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ

Á

ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ

− Overhaul at the factory all automatic detectors

a) conventional detectors SynoLINE
b) addressable detectors SynoLOOP

ÁÁÁ

ÁÁÁ

ÁÁÁ

ÁÁÁ

ÁÁÁ

ÁÁÁ

ÁÁÁ

ÁÁÁ

ÁÁÁ

ÁÁÁ

ÁÁÁ

ÁÁÁ

    1)

F

ÁÁÁ

ÁÁÁ

ÁÁÁ

ÁÁÁ

    2)

F

1) at the latest after 5 years if used in clean environment otherwise earlier
2) at the latest after 6 years if used in clean environment otherwise earlier
3) also refer to the corresponding detector manual

Summary of Contents for Synova FC330A









































































































































Reviews:

No comments

Related manuals for Synova FC330A

Wheelock MT-12/24 Installation Instructions Manual preview
MT-12/24
Brand: Wheelock Pages: 6
FireClass FC420CP Quick Manual preview
FC420CP
Brand: FireClass Pages: 4
E2S GNExCP7-PT-D Instruction Manual preview
GNExCP7-PT-D
Brand: E2S Pages: 8
E2S GNExCP7-PB-D Instruction Manual preview
GNExCP7-PB-D
Brand: E2S Pages: 13
GE Interlogix FP1500 Manual For Installation, Configuration And Commissioning preview
Interlogix FP1500
Brand: GE Pages: 57
Plumis Automist Series Technical Manual preview
Automist Series
Brand: Plumis Pages: 28
usi MIC1509S Quick Reference Manual preview
MIC1509S
Brand: usi Pages: 2
usi UNIVERSAL 2995CN Instructions Manual preview
UNIVERSAL 2995CN
Brand: usi Pages: 10
usi MP117 Instructions Manual preview
MP117
Brand: usi Pages: 10

Brands by name

Popular brands

Load more brands