Siemens SIWAREX WP251 Manual Download Page 84

Page: 84 / 220

Scale parameters and functions

8.7 DR 6 Limits

SIWAREX WP251

Manual, 12/2015, A5E37203357A

Variable

Note

Type

Length

(bytes)

Default

Min.

Max.

Modbus
Register

Reserve

DINT

maxi-

mum

num-

ber

range+

1246

Limit value 1 ON, limit

value 2 ON, limit

value 1 OFF, limit

value 2 OFF

(Page 84)

Switch-on point for

Limit 2

FLOAT

maxi-

mum

num-

ber

range

maxi-

mum

num-

ber

range

1248

Reserve

DINT

maxi-

mum

num-

ber

range+

1250

Limit value 1 ON, limit

value 2 ON, limit

value 1 OFF, limit

value 2 OFF

(Page 84)

Switch-off point for

Limit 2

FLOAT

maxi-

mum

num-

ber

range

maxi-

mum

num-

ber

range

1252

Switch-on delay limit

3 (empty)

Switch-on delay

Limit 3 (ms)

TIME

maxi-

mum

num-

ber

range+

1254

Limit 3 - empty

(Page 85)

Limit "empty" ON

(always references

the gross weight).

Unit is dependent

on "Limit refer-

ence".

FLOAT

maxi-

mum

num-

ber

range

maxi-

mum

num-

ber

range

1256

Switch-on/off delay

limit 1 & 2

Switch-on and

switch-off delay for

limit 1 and 2 (ms)

TIME

maxi-

mum

num-

ber

range+

1258

Reserve

FLOAT

1260

Reserve

USHORT

1262

Reserve

USHORT

1263

8.7.2

Limit value 1 ON, limit value 2 ON, limit value 1 OFF, limit value 2 OFF

The switch-on and switch-off points can be specified separately for each limit as a

percentage of the measuring range or as absolutely values (based on "Limit reference"

parameter setting). This allows both minimum and maximum value violation monitoring with

hysteresis. A delay time for switch-on and switch-off can also be specified. Either the current

net weight or the current gross weight can be selected as the reference value for limits 1 and

Summary of Contents for SIWAREX WP251





























































































































































































































Search results

Summary of Contents for SIWAREX WP251

Reviews:

Brands by name

Popular brands

Siemens SIWAREX WP251, Manual

Search results

Summary of Contents for SIWAREX WP251

Reviews:

Brands by name

Popular brands