manualshive.com logo in svg

Siemens SIWAREX WP251, Manual

Share
Download
Siemens SIWAREX WP251 Manual Download Page 19

SIWAREX WP251 
Manual, 12/2015, A5E37203357A 

19

 

Description 

3

3.1

 

Product overview 

SIWAREX WP251 is a versatile and flexible weighing module that can be used for operation 

as a non-automatic weighing instrument. 
The electronic weighing system can be used in SIMATIC S7-1200 and uses all features of a 

modern automation system, such as integrated communication, operator control and 

monitoring, the diagnostic system as well as the configuration tools in the TIA Portal. 

3.2

 

Area of application 

SIWAREX WP251 is the optimum solution wherever fast and precise dosing and filling are 

required. The typical applications of SIWAREX WP251 are: 

●

Automatic catchweighing instruments 

●

Gravimetric filling instruments

 (AWI)

●

Non-automatic weighing instrument (NAWI)

●

Weighing instruments in hazardous areas (with Ex interface SIWAREX IS)

3.3

 

System integration in SIMATIC 

The electronic weighing system described here is a technology module for SIMATIC S7-

1200. The system, including the weighing application, can be configured as desired in the 

automation solution. You can create optimal solutions for small and medium-sized plants by 

combining the suitable SIMATIC modules. You can create customized or industry-specific 

solutions in no time with the help of the configuration package available under the "Ready for 

use" application for SIMATIC.  

Note 
The direct use of SIWAREX WP251 with fail-safe SIMATIC S7-1200 controllers is not yet 

supported. 

Summary of Contents for SIWAREX WP251





























































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands