Siemens SIWAREX WP251 Manual Download Page 130

Page: 130 / 220

Scale parameters and functions

8.24 DR 25 Dosing device parameters

SIWAREX WP251

130

Manual, 12/2015, A5E37203357A

8.24.8

Weighing start options

This parameter defines the first action of an automatic dosing cycle to be executed (weighing

step 1). The following options are available:

Function

code

Meaning

The dosing starts directly without zero setting or taring

WP251 sets the scale to zero and then starts the dosing operation

2 (default)

WP251 tares the scale and then starts the dosing operation

WP251 tares the scale using the preset tare weight from DR 15 and then starts the

dosing operation

WP251 tares the scale using the preset tare weight from the SIMATIC I/O and then

starts the dosing operation

8.24.9

Cycle time for automatic zero setting

This parameter can be used to define a time after which zero setting or taring must have

occurred. The setting is made in milliseconds (ms). When "OIML" is set in DR 3, a zero

setting/taring occurs at the latest as defined in the regulations. Dependent on the maximum

time setting

8.24.10

Number of weighings without automatic taring/zero setting

This parameter defines a number of dosing cycles that are not zeroed or tared. It applies

only during continuous operation. The first cycle of the continuous operation is always

zeroed or tared (if configured for "Dosing start").

8.24.11

Check stop

This parameter enables, in contrast to transitions, the dosing cycle to be stopped after each

individual weighing step. By setting bits 0 … 7, corresponding check stops are set for

weighing steps 0 … 7. In addition, the "Activate check stop (1122)" command must be

issued in order to stop the cycle at the first set check stop point.
Example:

●

The check stop bits are set for weighing steps 1 and 2 and DR 25 is transmitted to

WP251.
The "Activate check stop (1122)" command is issued.

→ The "Check stop follows" bit is set in the AWI Status.

●

Dosing is started (single dosing or continuous operation)

→ After weighing step 1 is complete, WP251 jumps to "Stopped" st

ate. The "Check stop

active" bit is set in the AWI Status, and the "Check stop follows" bit is reset.

Summary of Contents for SIWAREX WP251





























































































































































































































Search results

Summary of Contents for SIWAREX WP251

Reviews:

Brands by name

Popular brands

Siemens SIWAREX WP251, Manual

Search results

Summary of Contents for SIWAREX WP251

Reviews:

Brands by name

Popular brands