manualshive.com logo in svg

Siemens SIWAREX WP251, Manual

Share
Download
Siemens SIWAREX WP251 Manual Download Page 193

 

Communication with SIMATIC S7-1200 

 

11.2 Communication via Modbus 

SIWAREX WP251 
Manual, 12/2015, A5E37203357A 

193

 

 

 

Note 
If execution of the function block is faulty, the variables shown do not correspond to the 

actual status in the module. 

 

11.2

 

Communication via Modbus 

11.2.1

 

Introduction 

The current process values and parameters can be exchanged via the RS485 interface with 

Modbus RTU or the Ethernet interface with Modbus TCP/IP. It is possible to use both 

interfaces for the communication. 

 

 

Note 
The SIWAREX WP251 is intended for operation in secure (closed) networks and does not 

have any protection against unauthorized data traffic. 

 

The following chapters describe the specifications for handling communication. The following 

functions can be executed: 

●

 

Export parameters from the electronic weighing system 

●

 

Write parameters 

●

 

Export current process values 

●

 

Monitor messages 

11.2.2

 

Principle of data transmission 

This description is valid for communication via Modbus RTU and Modbus TCP/IP.  
The standardized MODBUS protocol is used for communication. The master function is 

always in the connected communication partner, while the SIWAREX module is always the 

slave. 
Data transfer is bidirectional. The master function is always in the connected module which 

“controls” the communication with corresponding requests to the respective SIWAREX 

module address. The SIWAREX module is always the slave and responds to the requests of 

the master, provided that the address matches, with a response frame. 
Each Modbus partner has its own address. The SIWAREX module has the default address 

1. This address can be changed as a parameter (e.g. in SIWATOOL). This address is 

without significance if the Ethernet interface is used because the connection is based on the 

IP address. 

Summary of Contents for SIWAREX WP251





























































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands