manualshive.com logo in svg

Siemens SIWAREX WP251, Manual

Share
Download
Siemens SIWAREX WP251 Manual Download Page 68

Scale parameters and functions 

 

8.3 DR 3 Calibration parameters 

 

SIWAREX WP251 

68

 

Manual, 12/2015, A5E37203357A 

The calibration weights must be at least 5% of the nominal load of the scale and must differ 

from one another by an amount of at least 5% of the nominal load. 

●

 

Calibration weight 0 = 0 kg 

●

 

Calibration weight 1 = at least 5% of the nominal load of the scale 

●

 

Calibration weight 2 = at least 10% of the nominal load of the scale 

The calibration digits are determined automatically by the calibration commands and 

assigned to the respective calibration weights. Therefore, the digits do not have to specified! 

8.3.9

 

Scale interval 

The numerical increment for the weighing range can be specified in accordance with 

EN 45501 (0.0001 to 50). It defines the smallest indicated weight change and conforms to 

the accuracy of the overall system for scales requiring official calibration. 

8.3.10

 

Zero by power-on 

The scales can automatically be set to zero when the supply voltage is switched on (in legal 

trade operation, this is at the end of the startup waiting time). A weight of ±10 % of the 

maximum measuring range can be set to zero by power-on for legal trade scales. 
  

 

 

NOTICE 

If the scales are not being used in legal trade operation (no OIML restrictions), fully loaded 

scales can also be set to zero once this function is enabled. The function can, however, be 

limited by setting a maximum and minimum weight for zero by power-on. See the section 

on maximum and minimum weights for zero by power-on. 

 

8.3.11

 

Zero by power-

on when tare ≠ 0

 

The scale can be automatically set to zero when the supply voltage is switched on. If the 

Initial zeroing (Page 68) function is enabled, this still does not specify whether the initial 

zeroing is also to be performed when the tare weight in the tare memory is not equal to zero. 
If the "Initial zeroing if tared" parameter is set, the tare weight is also be cleared upon initial 

zeroing; if the parameter is not set, the scale is not set to zero. 

8.3.12

 

Automatic zero adjustment 

If necessary, the scales can be set semi-automatically to zero by the user by means of the 

"Zeroing" command. 

Summary of Contents for SIWAREX WP251





























































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands