manualshive.com logo in svg

Siemens SIWAREX WP251, Manual

Share
Download
Siemens SIWAREX WP251 Manual Download Page 191

 

Communication with SIMATIC S7-1200 

 

11.1 Integration in SIMATIC S7-1200 

SIWAREX WP251 
Manual, 12/2015, A5E37203357A 

191

 

11.1.5

 

I/O interface of function block 

The instance data block of the function block provides the "s_IO_DATA" structure. All 

parameters in this structure are updated cyclically by WP251 to SIMATIC. Thus, all values 

within the structure can be used directly – without reading or writing data records! The 

following parameters are available for use within "s_IO_DATA" on the factory side. 

 

Image 11-7  s_IO_DATA 

 

Parameter (read) 

Meaning 

AWI Status 

AWI Status bits according to data record 30 

PROCESS_VAL_1 

Process value according to setting in data record 14 in REAL format (default=gross/net weight) 

PROCESS_VAL_2 

Process value according to setting in data record 14 in REAL format (default=NAWI Status bits 

according to data record 30) 

dw_PROCESS_VAL_1 

Process value according to setting in data record 14 in DWORD format (default=gross/net 

weight) 

dw_PROCESS_VAL_2 

Process value according to setting in data record 14 in DWORD format (default=NAWI Status 

bits according to data record 30) 

AWI Status 

AWI Status bits according to data record 30 

OPERATION_ERRORS 

Operating errors according to the "Messages" section 

Summary of Contents for SIWAREX WP251





























































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands