manualshive.com logo in svg

Siemens SIWAREX WP251, Manual

Share
Download
Siemens SIWAREX WP251 Manual Download Page 188

Communication with SIMATIC S7-1200 

 

11.1 Integration in SIMATIC S7-1200 

 

SIWAREX WP251 

188

 

Manual, 12/2015, A5E37203357A 

11.1.3

 

Calling of function block 

This description is based on use of the "WP251" block with data record communication and 

the following data: 

●

 

Start address SIWAREX WP251: 68 (see 

→ 

Creating the hardware configuration 

(Page 186)) 

●

 

HW ID 

SIWAREX WP251: 271 (see → 

Creating the hardware configuration (Page 186)) 

●

 

Instance data block number of SIWAREX WP251 function block: DB 251 

The function block can be integrated at the desired position in the user program using drag 

and drop. Calling of the FB must be carried out cyclically in the control program. 

 

Image 11-5  Block WP251PR 

 

Function block parameter 

Description 

ADDR 

Start address WP251 (see → 

Creating the hard-

ware configuration (Page 186)) 

HW_ID 

HW ID WP251 (see → 

Creating the hardware 

configuration (Page 186)) 

DB_NO 

Number of FB-internal instance DB 

LIFEBIT 

Optional status bit can be used to monitor com-

munication 

The generated instance DB (DB251 in this case) contains all data records of the WP251 as 

well as all parameters required to exchange data between the CPU and weighing module. 
A separate FB call must be made in the user program for each weighing module. In this 

manner, each scale receives its own instance DB which provides the respective scale 

parameters. The input and output parameters of the FB must be matched to the respective 

WP251 for each call. 

Summary of Contents for SIWAREX WP251





























































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands