manualshive.com logo in svg

Siemens SITRANS FX330, Operating Instructions Manual, Page: 89 / 116

Share
Download
Siemens SITRANS FX330 Operating Instructions Manual Download Page 89

 OPERATION 

6

89

SITRANS FX330

www.siemens.com/flow

05/2016 - A5E36751269-AA

S

Sensor

Flow Meas. Out of Spec.

The vortex frequency or the 

volume flow is out of range. 

The real flow is higher or 

lower than the indicated 

value.

Check the process 

conditions.

Low Flow Cutoff Undercut

Volume flow is lower than 

low flow cutoff (LFC)

Check the low flow cut-off or 

the process conditions.

Weak Flow Meas. Signal

The vortex signal is too weak 

or disturbed.

Check the process 

conditions and the 

installation situation. 

Eliminate external 

disturbances. If the 

message recurs, contact the 

manufacturer.

Pres.Sen.Temp. Out of Spec. Temperature of the 

pressure sensor out of 

specification

Make sure that the device is 

operated within the 

permissable temperature 

range.

Elec. Temp. Out Of Spec.

The electronic temperature 

of the sensor module is out 

of specification.

S

Electronics

Elec. Temp. Out Of Spec.

The electronic temperature 

of the converter is out of 

specification.

Make sure that the device is 

operated within the 

permissable temperature 

range.

S

Process

CO Undersaturation

The measurement value is 

lower than the lower range 

value of the current output. 

The current output is 

saturated and does not 

reflect the effective 

measuring value.

Check the process 

conditions and the lower 

current output limit.

CO Oversaturation

The measurement value is 

higher than the upper range 

value of the current output. 

The current output is 

saturated and does not 

reflect the effective 

measuring value.

Check the process 

conditions and the upper 

current output limit.

M

Sensor

Faulty Sensor Oscillator

The sensor oscillator is 

working out of range.

Perform a hard reset. If the 

message recurs, contact the 

manufacturer.

M

Electronics

Faulty Converter Oscillator

The converter oscillator is 

working out of range.

Perform a hard reset. If the 

message recurs, contact the 

manufacturer.

Status 
type

Event group

Single event

Description

Actions to eliminate the 
event

Summary of Contents for SITRANS FX330





















































































































Reviews:

No comments