manualshive.com logo in svg

Siemens SITRANS FX330, Operating Instructions Manual, Page: 88 / 116

Share
Download
Siemens SITRANS FX330 Operating Instructions Manual Download Page 88

6

 OPERATION 

88 

SITRANS FX330

www.siemens.com/flow

05/2016 - A5E36751269-AA

F

Configuration

Inconsistent NVRAM

Inconsistent data in the 

parameter memory

Perform a hard reset. If the 

message recurs, contact the 

manufacturer.

Error Starting SIL Mode

Error in starting SIL mode

Perform the SIL starting 

process as described in the 

safety manual. If the 

message recurs, contact the 

manufacturer.

CO Float Error

Error in processing of the 

measuring value due to 

inconsistent set of 

parameter.

Load the factory settings 

and perform a hard reset. If 

the message recurs, contact 

the manufacturer.

NVRAMs Mismatch

Incompatible serial 

numbers of display and 

electronic module

Use displays and electronic 

modules, which belong 

together. Contact the 

manufacturer, if necessary.

Conv. NVRAM Layout Error

Incompatible data in 

parameter memory

Perform a hard reset. If the 

message recurs, contact the 

manufacturer.

Disp. NVRAM Layout Error

Incompatible data after 

firmware update

Perform a hard reset. If the 

message recurs, contact the 

manufacturer.

C

Sensor

Sensor FW Update

A firmware update of the 

sensor module has been 

started.

Wait for firmware update to 

finish.

C

Electronics

Converter FW Update

A firmware update of the 

converter module has been 

started.

Wait for firmware update to 

finish.

C

Configuration

Sensor Sim. Active

A simulation of the sensor is 

active

Stop the simulation of the 

sensor variables

Current Out. Sim. Active

A simulation of the current 

output is active

Stop the simulation of the 

current output variables

Current In. Sim. Active

A simulation of the current 

input is active

Stop the simulation of the 

current input variables

HART Sim. Active

Simulation of a measuring 
value via HART

®

 interface

Stop the simulation via the 
HART

®

 interface.

Flow Comp. Sim. Active

A simulation of 

measurement value 

processing is active.

Stop the simulation of the 

measurement value 

processing.

Binary Output Sim. Active

A simulation of the binary 

output is active

Stop the simulation of the 

binary output variables

Totalizer Sim. Active

A simulation of the totalizer 

is active

Stop the simulation of the 

totalizer variables

SIL Prooftest

Device is in maintenance 

mode 3 (proof test for SIL)

Perform the test according 

to the instruction in the 

safety manual.

Parameterization Test

Device is in maintenance 

mode 3 (parameterization 

test)

Status 
type

Event group

Single event

Description

Actions to eliminate the 
event

Summary of Contents for SITRANS FX330





















































































































Reviews:

No comments