manualshive.com logo in svg

Siemens SITRANS FX330, Operating Instructions Manual, Page: 73 / 116

Share
Download
Siemens SITRANS FX330 Operating Instructions Manual Download Page 73

 OPERATION 

6

73

SITRANS FX330

www.siemens.com/flow

05/2016 - A5E36751269-AA

A11.6 Application Assistant - FAD

.17 1. Meas. Page

Same options as in A11.1.13.

.18 2. Meas. Page

Same options as in A11.1.14.

Function

Setting / Description

This application assistant is available if meter type is set to "Heat & Dens. & FAD" (refer to "C6.3 Extras").

.1

.2 Units

.2.1 Volume Flow

Select unit (default: according to order specification or m

3

/h).

.2.2 Norm. Vol. Flow

Select unit (default: according to order specification or Nm

3

/h).

.2.3 Volume

Select unit (default: according to order specification or m

3

).

.2.4 Norm. Volume

Select unit (default: according to order specification or Nm

3

).

.2.5 Temperature

Select unit (default: according to order specification or 

°

C).

.2.6 Pressure

Select unit (default: according to order specification or bar).

.2.7 Density

Select unit (default: according to order specification or kg/m

3

).

.3 Process

.3.1 Fluid

Select "Gas".

.3.2 Medium

Select "Air".

.3.3 Time Constant

0...100 s

.3.4 Low Flow Cutoff

Enter low flow cutoff point in current volume flow unit.

.4 Current Input

Same options as in A11.3.4.

.5.1 Temp. Source1

Internal / External / External HART / Not Available

.5.2 Temp. Source2

Internal / External / External HART / Not Available

Temperature source 1 and 2 must be different.

.6 Gas

.6.1 Inlet Temperature

Enter temperature on inlet side in selected unit.

.6.2 Atm. Pressure

Enter current ambient pressure in selected unit.

.6.3 Filter Pressure Drop

Enter filter pressure drop in selected unit.

.6.4 Inlet Rel. Humidity

Enter air humidity on inlet side in 0

…

100%.

.6.5 Outlet Rel. Humidity

Enter air humidity on outlet side in 0

…

100%.

.6.6 Compressor RPM

Compressor revolutions per minute.

.6.7 Rated Compr. RPM

Rated compressor revolutions per minute.

.7 Operating Values

Same options as in A11.1.4.

.8 Current Output

Select "FAD".

.9 Binary Output

Same options as in A11.1.6.

.10 Pulse Output

Same options as in A11.1.7.

.11 Frequency Output

Same options as in A11.1.8.

.12 Status Output

Same options as in A11.1.9.

.13 Limit Switch

Same options as in A11.1.10.

.14 Flow Totalizer

Same options as in A11.1.11.

.16 1. Meas. Page

Same options as in A11.1.13.

.17 2. Meas. Page

Same options as in A11.1.14.

Function

Setting / Description

Summary of Contents for SITRANS FX330





















































































































Reviews:

No comments