manualshive.com logo in svg

Siemens SITRANS FX330, Operating Instructions Manual, Page: 46 / 116

Share
Download
Siemens SITRANS FX330 Operating Instructions Manual Download Page 46

4

 ELECTRICAL CONNECTIONS 

46 

SITRANS FX330

www.siemens.com/flow

05/2016 - A5E36751269-AA

4.6  Ingress protection

The signal converter electronics housing meets the requirements for IP66/67 in accordance with 
EN 60529 both for the compact and for the remote version.

Therefore it is essential to observe the following points:

•  

Use only original gaskets. They must be clean and free of any damage. Defective gaskets must 

be replaced.

•  

The electrical cables used must be undamaged and must comply with regulations.

•  

The cables must be laid with a loop 

1

 upstream of the measuring device to prevent water 

from getting into the housing.

•  

The cable feedthroughs 

2

 must be tightened. Note that the clamping range of the cable 

feedthrough corresponds to the outer diameter of the cable.

•  

Align the measuring device so that the cable feedthrough is never facing up 

3

.

•  

Close any unused cable feedthroughs using blind plugs 

4

 suitable for the protection category.

•  

Do not remove the required cable bushing from the cable feedthrough.

CAUTION!

After all servicing and maintenance work on the measuring device, the specified ingress 
protection category must be ensured again.

Figure 4-10: Cable feedthrough

Summary of Contents for SITRANS FX330





















































































































Reviews:

No comments