manualshive.com logo in svg

Siemens SITRANS FX330, Operating Instructions Manual, Page: 13 / 116

Share
Download
Siemens SITRANS FX330 Operating Instructions Manual Download Page 13

 DEVICE DESCRIPTION 

2

13

SITRANS FX330

www.siemens.com/flow

05/2016 - A5E36751269-AA

2.1  Scope of delivery

2.2  Device versions

The devices are delivered in the following variants:

•

Signal converter with display

•

Flow sensor in flanged design, flow sensor F

•

Flow sensor in sandwich design, flow sensor S

•

Remote version - Flow sensor with separated remote signal converter

•

Dual version with two flow sensors and two signal converters

The following designs are available as options:

•

With pressure sensor - with or without shut-off valve

•

Flange version, flow sensor with single reduction F1R

•

Flange version, flow sensor with double reduction F2R

INFORMATION!

Inspect the packaging carefully for damages or signs of rough handling. Report damage to the 
carrier and to the local office of the manufacturer.

INFORMATION!

Do a check of the packing list to make sure that you have all the elements given in the order.

INFORMATION!

Look at the device nameplate to ensure that the device is delivered according to your order. 
Check for the correct supply voltage printed on the nameplate.

Figure 2-1: Scope of delivery

1  

Measuring device in ordered version

2  

Manual

3  

Certificates, calibration report and parameter data sheet

4  

Bar magnet

Summary of Contents for SITRANS FX330





















































































































Reviews:

No comments