Siemens SIMOTICS CONNECT 600 Operating Instructions Manual Download Page 52

Page: 52 / 80

9. Connect the power cable to the following terminals as shown in the terminal diagram.

– CE version: L1, N and PE at terminals

⑨

– UL version: L1 and N at the rotary disconnection device

⑩

, PE at terminal

⑨

10.Connect all of the cables at the terminal block

⑧

as shown in the terminal diagram.

11.Tighten the cable glands

⑤

correctly so that the degree of protection of the connectivity

module is guaranteed.

12.Attach the shield connection clamp to the terminal block

⑧

. Carefully ensure that all of the

cables are not strained.

13.Close the miniature circuit breaker

①

14.Close the sensor box door. For the UL version of the connectivity module, follow the

instructions provided in Chapter Only UL version: Opening and closing the sensor box door
(Page 25).

Maintenance
9.7 Replacing connectivity module components

Operating Instructions, 06/2020

Summary of Contents for SIMOTICS CONNECT 600

















































































Search results

Summary of Contents for SIMOTICS CONNECT 600

Reviews:

Related manuals for SIMOTICS CONNECT 600

Brands by name

Popular brands

Siemens SIMOTICS CONNECT 600, Operating Instructions Manual

Search results

Summary of Contents for SIMOTICS CONNECT 600

Reviews:

Related manuals for SIMOTICS CONNECT 600

Brands by name

Popular brands