Siemens SIMOTICS CONNECT 600 Operating Instructions Manual Download Page 58

Page: 58 / 80

14.Under "Static > SM1281 Config", set the start value of parameter "S7lead?" to TRUE.

15.Load the software to the device.

When requested to do so, enter the password specified under step 8 of the previous handling
instructions (restoring the configuration for CPU SIMATIC S7-1212C DC/DC/DC).
A note to log out is displayed in the web interface.

16.In the web interface, confirm the login with "OK".

After approximately 1 minute, the operating mode switches to "RUN: X-Tools".

17.Once the operating mode has switched to "RUN: X-Tools", withdraw the LAN cable from the

LAN connection

②

18.Reconnect the internal LAN cable to the LAN connection

②

19.Close the sensor box. For the UL version of the connectivity module, follow the instructions

provided in ChapterOnly UL version: Opening and closing the sensor box door (Page 25).

9.9

Changing the password for X-Tools

Precondition

• A Remote Desktop Connection has been established from the local service PC to the IPC.

• The password (Page 19) for X-Tools is known.

Procedure

1. Open X-Tools on the IPC.

2. Open the "Servers" element in the "Main Management System" configuration window.

Maintenance
9.9 Changing the password for X-Tools

Operating Instructions, 06/2020

Summary of Contents for SIMOTICS CONNECT 600

















































































Search results

Summary of Contents for SIMOTICS CONNECT 600

Reviews:

Brands by name

Popular brands

Siemens SIMOTICS CONNECT 600, Operating Instructions Manual

Search results

Summary of Contents for SIMOTICS CONNECT 600

Reviews:

Brands by name

Popular brands